Unsolved
This post is more than 5 years old
40 Posts
0
17596
April 28th, 2016 08:00
Changing IP address of Array
We are moving our DR site storage into production and need to change the IP's of both management adn iSCSI. Everytime i try to do this, either from command line or GUI i keep getting the message..."There must be at least one member network interface on the same subnet
as the management address". i believe i tried what it ask and still cannot change it. i can change one or both of the iSCSI ports but not n the management port. I am STUCK! Can anyone get me past this?? Any help is greatly appreciated. Thank you in advance.
PS-4100 with 1mgmt port and 2 iSCSI ports
changeing mgmt from 10.1.50.X to 10.0.70.X
Changing iSCSI from 10.1.74.x to 10.0.74.x
Perry
No Events found!
bigpoamah
40 Posts
0
April 29th, 2016 09:00
Don,
I disables teh management nic then loggeed in thru serial port and tried to change mgmt ip and still got that message. i tried to change one of teh other nics to the same IP subnet and that changed that NIC but i still can't get the mgmt ip to change. HELP!!!!
bigpoamah
40 Posts
0
April 29th, 2016 09:00
Don,
I got past that ppoint and was abel to remove ip adress from mgmt. The command i uses was
management-network show
bigpoamah
40 Posts
0
April 29th, 2016 09:00
The eth 2 was disabled when i looked at it.
MWNSMSH> member select SAN1
MWNSMSH(member_SAN1)> eth sel 2 show
_______________________________ Eth Information _______________________________
Name: eth2 Status: down
Changed: Fri Apr 29 09:48:12 2016 Type: ethernet-csmacd
DesiredStatus: down Mtu: 1500
Speed: 100 Mbps HardwareAddress: D4:AE:52:9E:35:9A
IPAddress: 10.1.50.71 NetMask: 255.255.255.0
IPv6Address: Description: MGMT PORT
SupportsManagement: only ManagementStatus: mgmt
DCB: off
________________________________________
when i go to show management ip i get this.
MWNSMSH(grpparams)> managemnt-network show ip address
^
Error: Bad command
MWNSMSH(grpparams)> management-network show ip address
Error: Too many parameters
MWNSMSH(grpparams)> management-network show ip Address
Error: Too many parameters
MWNSMSH(grpparams)> management-network show ip Address
Error: Too many parameters
what am i doing wrong. it shouldn't be that hard and i'm not that stupid. I don't think. lol
bigpoamah
40 Posts
0
April 29th, 2016 10:00
stuck again. i want to say thank you VERY much for all the help. I really do appreciate teh expertise.
MWNSMSH(grpparams)> management-network show
Ip Address
----------------------------------------------------------------
MWNSMSH(grpparams)> exit
MWNSMSH> member select SAN1
MWNSMSH(member_SAN1)> eth sel 2 show
_______________________________ Eth Information _______________________________
Name: eth2 Status: down
Changed: Fri Apr 29 09:48:12 2016 Type: ethernet-csmacd
DesiredStatus: down Mtu: 1500
Speed: 100 Mbps HardwareAddress: D4:AE:52:9E:35:9A
IPAddress: 10.1.50.71 NetMask: 255.255.255.0
IPv6Address: Description: MGMT PORT
SupportsManagement: only ManagementStatus: mgmt
DCB: off
_______________________________________________________________________________
MWNSMSH(member_SAN1)> eth sel 2 mgmt-only disable
% Error - The interface is dedicated to management operations only and is not al
lowed to be configured for iSCSI access.
MWNSMSH(member_SAN1)>
bigpoamah
40 Posts
0
April 29th, 2016 11:00
Don,
The biggest reason i am on the support forumn is because we no longer have support for this SAN. We are just trying to offload soe of our non critical servers to this storage in teh interim untl we upgrade our current storage. I am into the GUI now but now i need to change the other two IP's of teh iSCSI NICs and getting teh same message about being on the same subnet as the management. i have a pretty good grip on teh CLI but still not sure why i keep geting that message. Thanks again for ALL your help. I appreciate it more than you know. Thanks again!