Browse Community
Help
Log In
Responses(3)
Solutions(0)
machiasiaweb2
110 Posts
0
January 8th, 2013 07:00
Good day,
What model switch is this?
Ans: That is dell 3448
What revision of firmware is the switch at?
Ans:
SW version 2.0.0.34 ( date 25-Jul-2010 time 14:24:24 )
Boot version 1.0.1.01 ( date 15-Jun-2006 time 11:42:56 )
HW version 00.00.01
What type of device is associated with this MAC address? Is it plugged into port 25? Have you tried the command leaving the ethernet e25 left off?
That is a server and plugged to port 25. It can shown its learned MAC address when using command
show bridge address-table
Thanks!
January 8th, 2013 18:00
Yes. that IP and MAC also owned by server and connected to Ethernet e25 directly.
It is not possible to run the command you advise.
console(config)# arp 120.120.133.1 84:EF:2D:0A:6C:1F ethernet 1/e25
% bad parameter value
Can be learned by
console# show bridge address-table ethernet e25
Aging time is 300 sec
Vlan Mac Address Port Type
-------- --------------------- ------ ----------
1 84:2b:2b:0a:6b:1f e25 dynamic
is it related to vlan 1 setting, because the ip address of vlan 1 is set to different subnet
interface vlan 1
ip address 192.168.168.201 255.255.255.0
thanks!
January 9th, 2013 06:00
Hello,
I have done a some config which is added 120.120.133.100 into vlan 1. It will learn some other some
# show arp
ARP timeout: 60000 Seconds
VLAN Interface IP address HW address status
--------------------- --------------- ------------------- ---------------
vlan 1 e1 192.168.168.200 00:78:51:9d:50:bb dynamic
vlan 1 192.168.168.211 00:1F:51:01:d2:22 dynamic
vlan 1 e1 120.120.133.13 00:34:dd:0b:a1:07 dynamic
However it still can learn e25 information.
But after I ping 120.120.133.100 - vlan 1 IP.. It can learn the arp information
vlan 1 e25 120.120.133.1 84:EF:2D:0A:6C:1F dynamic
Did you know why?
Dell Support Resources
View All
Top
machiasiaweb2
110 Posts
0
January 8th, 2013 07:00
Good day,
What model switch is this?
Ans: That is dell 3448
What revision of firmware is the switch at?
Ans:
SW version 2.0.0.34 ( date 25-Jul-2010 time 14:24:24 )
Boot version 1.0.1.01 ( date 15-Jun-2006 time 11:42:56 )
HW version 00.00.01
What type of device is associated with this MAC address? Is it plugged into port 25? Have you tried the command leaving the ethernet e25 left off?
Ans:
That is a server and plugged to port 25. It can shown its learned MAC address when using command
show bridge address-table
Thanks!
machiasiaweb2
110 Posts
0
January 8th, 2013 18:00
Yes. that IP and MAC also owned by server and connected to Ethernet e25 directly.
It is not possible to run the command you advise.
console(config)# arp 120.120.133.1 84:EF:2D:0A:6C:1F ethernet 1/e25
% bad parameter value
Can be learned by
console# show bridge address-table ethernet e25
Aging time is 300 sec
Vlan Mac Address Port Type
-------- --------------------- ------ ----------
1 84:2b:2b:0a:6b:1f e25 dynamic
is it related to vlan 1 setting, because the ip address of vlan 1 is set to different subnet
interface vlan 1
ip address 192.168.168.201 255.255.255.0
thanks!
machiasiaweb2
110 Posts
0
January 9th, 2013 06:00
Hello,
I have done a some config which is added 120.120.133.100 into vlan 1. It will learn some other some
# show arp
ARP timeout: 60000 Seconds
VLAN Interface IP address HW address status
--------------------- --------------- ------------------- ---------------
vlan 1 e1 192.168.168.200 00:78:51:9d:50:bb dynamic
vlan 1 192.168.168.211 00:1F:51:01:d2:22 dynamic
vlan 1 e1 120.120.133.13 00:34:dd:0b:a1:07 dynamic
However it still can learn e25 information.
But after I ping 120.120.133.100 - vlan 1 IP.. It can learn the arp information
# show arp
ARP timeout: 60000 Seconds
VLAN Interface IP address HW address status
--------------------- --------------- ------------------- ---------------
vlan 1 e1 192.168.168.200 00:78:51:9d:50:bb dynamic
vlan 1 192.168.168.211 00:1F:51:01:d2:22 dynamic
vlan 1 e1 120.120.133.13 00:34:dd:0b:a1:07 dynamic
vlan 1 e25 120.120.133.1 84:EF:2D:0A:6C:1F dynamic
Did you know why?