Dell Powerconnect 5424 vlan setup/issues

Question

I am having problems with the initial configuration of my new switches.The basic network architecture that i trying to accomplish:2 switchs that are going to be configured identical for fallover ( ethernet channel bonded connections).Each switch will have 2 vlans with 10 connection per vlan.vlan10 will have the 10.0.10.x networkvlan20 will have the 10.0.0.x networkI will have a load balancer directing the traffic from one network the other. The loadbalancers interface will be 10.0.10.254 & 10.0.0.254. This should be the only communication point for the vlans.I have setup 2 basic vlans as described but I am running into problems.Vlan10 is configured and working fine, all nodes connect with the swich and communicate and they can all connect to there gateway 10.0.10.254.Vlan 20 does not work correctly. Some nodes can connect to the switch for management via telnet others can not and none of the nodes can communicate with each other.I am quite new to the configuration of these type of switch and looking for some input on my problems....show running-configvlan databasevlan 10,20exitinterface range ethernet g(1-10)switchport access vlan 10exitinterface range ethernet g(11-20)switchport access vlan 20exit interface vlan 10exitvoice vlan oui-table add 0001e3 Siemens_AG_phone________voice vlan oui-table add 00036b Cisco_phone_____________voice vlan oui-table add 00096e Avaya___________________voice vlan oui-table add 000fe2 H3C_Aolynk______________voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phonevoice vlan oui-table add 00d01e Pingtel_phone___________voice vlan oui-table add 00e075 Polycom/Veritel_phone___voice vlan oui-table add 00e0bb 3Com_phone______________iscsi target port 860 address 0.0.0.0iscsi target port 3260 address 0.0.0.0interface vlan 10ip address 10.0.10.100 255.255.255.0exitinterface vlan 20ip address 10.0.0.220 255.255.255.0exitaaa authentication enable default lineaaa authentication login default lineline telnetpassword xyz encryptedexitline sshpassword xyz encryptedexitline consolepassword xyz encryptedexitusername admin password xyz level 15 encryptedsnmp-server community Dell_Network_Manager rw view DefaultSuperDefault settings:Service tag: 1WHxxx SW version 1.0.0.31 (date 31-Oct-2007 time 10:32:13)Gigabit Ethernet Ports=============================no shutdownspeed 1000duplex fullnegotiationflow-control offmdix autono back-pressureinterface vlan 1interface port-channel 1 - 8spanning-treespanning-tree mode STPqos basicHere is a a bit more detail via the switch, In the output below g1-5 vlan10 functions perfectly.Now g11 can telnet / ping the switch ip but g14 cannot although the switch detects the port (if I cycle the port connection)...port 14 cycle output17-Jan-2000 20:26:22 %LINK-W-Down: g1417-Jan-2000 20:26:25 %LINK-I-Up: g1417-Jan-2000 20:26:55 %STP-W-PORTSTATUS: g14: STP status Forwarding...show interface statPort Type Duplex Speed Neg ctrl State Pressure Mode-------- ------------ ------ ----- -------- ---- ----------- -------- -------g1 1G-Copper Full 1000 Enabled Off Up Disabled Offg2 1G-Copper Full 1000 Enabled Off Up Disabled Ong3 1G-Copper Full 1000 Enabled Off Up Disabled Ong4 1G-Copper Full 1000 Enabled Off Up Disabled Ong5 1G-Copper Full 1000 Enabled Off Up Disabled Offg6 1G-Copper Full 1000 Enabled Off Up Disabled Ong7 1G-Copper -- -- -- -- Down -- --g8 1G-Copper -- -- -- -- Down -- --g9 1G-Copper -- -- -- -- Down -- --g10 1G-Copper Full 1000 Enabled Off Up Disabled Offg11 1G-Copper Full 100 Enabled Off Up Disabled Offg12 1G-Copper -- -- -- -- Down -- --g13 1G-Copper -- -- -- -- Down -- --g14 1G-Copper Full 1000 Enabled Off Up Disabled Offg15 1G-Copper -- -- -- -- Down -- --g16 1G-Copper -- -- -- -- Down -- --g17 1G-Copper -- -- -- -- Down -- --g18 1G-Copper -- -- -- -- Down -- --g19 1G-Copper -- -- -- -- Down -- --g20 1G-Copper Full 1000 Enabled Off Up Disabled Ong21 1G-Combo-C -- -- -- -- Down -- --g22 1G-Combo-C -- -- -- -- Down -- --g23 1G-Combo-C -- -- -- -- Down -- --g24 1G-Combo-C -- -- -- -- Down -- --Flow LinkCh Type Duplex Speed Neg control State-------- ------- ------ ----- -------- ------- -----------ch1 -- -- -- -- -- Not Presentch2 -- -- -- -- -- Not Presentch3 -- -- -- -- -- Not Presentch4 -- -- -- -- -- Not Presentch5 -- -- -- -- -- Not Presentch6 -- -- -- -- -- Not Presentch7 -- -- -- -- -- Not Presentch8 -- -- -- -- -- Not Present

sentinel-master · Answer

You might want to enable at a global level routing and routing at a vlan level so :

ip routing

vlan 10

routing

vlan 20

routing

Then it would be useful to see a copy of "show ip routing" to see the state of your routing/vlan table.

Networking General

Was this post helpful?