This post is more than 5 years old

1 Rookie

 • 

2 Posts

34322

June 24th, 2019 08:00

Port Channel config

Hi,

we have S4148T-ON.

i have configured LAG with another (cisco) switch with no issues.

i'm trying to configure another port-channel to connect with ESXi. (ESXi configured teaming, route based on IP hash, on notify switch)

below is my config. it was set also to active before i posted below.

any idea how to bring it on?

interface ethernet1/1/23
no shutdown
channel-group 2 mode passive
no switchport
!
interface ethernet1/1/24
no shutdown
channel-group 2 mode passive
no switchport

interface port-channel2
no shutdown
switchport mode trunk
switchport trunk allowed vlan 1000

-----------

show interface port-channel summary
LAG Mode Status Uptime Ports
1 L2-HYBRID up 3 weeks 4 days 09:3 Eth 1/1/53 (Up)
Eth 1/1/54 (Up)
2 L2-HYBRID down 00:00:00 Eth 1/1/23 (Inact)
Eth 1/1/24 (Inact)

show interface port-channel 2
Port-channel 2 is up, line protocol is down
Address is 68:4f:64:5f:b7:00, Current address is 68:4f:64:5f:b7:00
Interface index is 85886082
Internet address is not set
Mode of IPv4 Address Assignment: not set
Interface IPv6 oper status: Disabled
MTU 1532 bytes, IP MTU 1500 bytes
LineSpeed 0
Minimum number of links to bring Port-channel up is 1
Maximum active members that are allowed in the portchannel is 32
Members in this channel: Eth 1/1/23-1/1/24
ARP type: ARPA, ARP Timeout: 60
Last clearing of "show interface" counters: 01:06:51
Queuing strategy: fifo
Input statistics:
5558 packets, 399059 octets
33 64-byte pkts, 5444 over 64-byte pkts, 74 over 127-byte pkts
7 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
144 Multicasts, 5083 Broadcasts, 331 Unicasts
0 runts, 0 giants, 0 throttles
0 CRC, 0 overrun, 0 discarded
Output statistics:
46456 packets, 3468430 octets
39092 64-byte pkts, 4615 over 64-byte pkts, 2581 over 127-byte pkts
144 over 255-byte pkts, 24 over 511-byte pkts, 0 over 1023-byte pkts
20954 Multicasts, 23670 Broadcasts, 1832 Unicasts
0 throttles, 136 discarded, 0 Collisions, 0 wred drops
Rate Info(interval 30 seconds):
Input 0 Mbits/sec, 0 packets/sec, 0% of line rate
Output 0 Mbits/sec, 0 packets/sec, 0% of line rate
Time since last interface status change: 01:06:52

 

1 Rookie

 • 

2 Posts

June 25th, 2019 02:00

thanks! it is now working

following the pdf you attached, where Add port member — static LAG :

OS10(config)# interface ethernet 1/1/2

OS10(conf-if-eth1/1/2)# channel-group 10 mode on

it is working fine.

in the preveius PDF i followed, it was only 

exitOS10(config)# interface ethernet 1/1/2

OS10(conf-if-eth1/1/2)# channel-group 10

 

Moderator

 • 

9.6K Posts

 • 

42.5K Points

June 24th, 2019 11:00

Hi,

Try creating a static lag instead of lacp. Page 88 https://topics-cdn.dell.com/pdf/force10-s4048-on_reference-guide7_en-us.pdf

No Events found!

Top