34 Posts
0
4671
Trunk example S4810
Hello All,
Please share Trunk configuration for S4810. lets say I want to pass Vlan 100 to 500 on interface Ten. 0/1
Ten 0/1 is connected to another Dell S4810 switch.
34 Posts
0
4671
Hello All,
Please share Trunk configuration for S4810. lets say I want to pass Vlan 100 to 500 on interface Ten. 0/1
Ten 0/1 is connected to another Dell S4810 switch.
Top
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
August 11th, 2021 11:00
In that case, use switchport trunk allowed vlan 100,500 Page 408 https://dell.to/2X8Cgkr
DELL-Erman O
Moderator
Moderator
•
2.4K Posts
0
August 11th, 2021 02:00
Hello,
I found an example like this and hope this will useful
vlan-stack trunk
Specify a Layer 2 port or port channel as a trunk port to the stackable VLAN network.
To remove a trunk port designation from the selected interface, use the no vlan-stack trunk command.
This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
Prior to using this command, to place the interface in Layer 2 mode, use the switchport command.
To remove the trunk port designation, first remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs.
In Example 1, a VLAN-Stack trunk port is configured and then made part of a single-tagged VLAN.
In Example 2, the tag protocol identifier (TPID) is set to 88A8. The Te 3/10 port is configured to act as a VLAN-Stack access port; the Te 5/1 port acts as a VLAN-Stack trunk port, switching stackable VLAN traffic for VLAN 10, while also switching untagged traffic for VLAN 30 and tagged traffic for VLAN 40. (To allow VLAN 30 traffic, you need the native VLAN feature. Use the portmode hybrid command. For more information, see the portmode hybrid command.
mdgajjar
34 Posts
0
August 11th, 2021 10:00
Thanks and appreciate for your reply.
I am not using stack here. that's a just standalone switch. that trucking config is little bit confusing here.
mdgajjar
34 Posts
0
September 9th, 2021 10:00
I do not found switch port mode trunk command on my switch. can you please give me example. below is the versoin details.
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
September 9th, 2021 11:00
It should be the switchport command on OS9 instead of OS10. Page 737 https://dell.to/3DV7ht4
danmany
3 Posts
0
September 10th, 2021 02:00
Hello. I also have a problem with trunk settings on the port. Port is configured:
interface TenGigabitEthernet 0/2
no ip address
switchport
switchport mode private-vlan trunk
no shutdown
This is not working
I have a task to miss all VLAN through the port
Help please
DELL-Marco B
Moderator
Moderator
•
3.5K Posts
0
September 10th, 2021 03:00
Hello,
please can you give us more details?
Is it a S4810? With OS version?
you said that with command switchport mode private-vlan trunk is not working. What do you want to configure and how?
Please post also the config of the switch.
Thanks
Marco
mdgajjar
34 Posts
0
September 10th, 2021 10:00
I want configured interface as trunk port. s4180 switch is connected to another dell. i want to allow some vlans on this trunk port. and switchport mode trunk is not working on this switch.
can you please share any example or just config on trunk/tag interface.
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
September 10th, 2021 10:00
Try
switchport mode trunk.
danmany
3 Posts
0
September 10th, 2021 12:00
Hello
This is your case:
SW5#configure
SW5(conf)#interface vlan 200
SW5(conf-if-vl-200)#tagged tengigabitethernet 0/2
SW5(conf-if-vl-200)#exit
SW5(conf)#interface vlan 500
SW5(conf-if-vl-500)#tagged tengigabitethernet 0/2
SW5(conf-if-vl-500)#exit
SW5(conf)#exit
SW5#show interfaces switchport tengigabitethernet 0/2
Codes: U - Untagged, T - Tagged
x - Dot1x untagged, X - Dot1x tagged
G - GVRP tagged, M - Trunk, H - VSN tagged
i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged
Name: TenGigabitEthernet 0/2
802.1QTagged: True
Vlan membership:
Q Vlans
T 1,200,500
danmany
3 Posts
0
September 10th, 2021 12:00
Hello
I used Dell S4810
OS version: Dell Application Software Version: 9.14(1.9P4)
I want to allow all vlans tagged on this trunk port.
Command: "switchport mode trunk" not in the menu
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
September 10th, 2021 13:00
Try the steps on page 957 https://dell.to/3ttoLIk