Unsolved
This post is more than 5 years old
3 Posts
0
54082
DRAC5 web interface lost
Hi,
I've some problem with my DRAC5 card.
I'm just configuring my new PowerEdge 2950; so I've installed OpenManage and give a valid IP to DRAC5 card through configuration tab, apply changes and seems all work fine, but if I try to access via web interface nothing happens, the DRAC5 web server doesn't reply. I've tried to plug directly to card and ping works fine, web interface no.
Through BIOS card I've not found some options that could help me....
Here my conf.
BMC
Attribute;Value
BMC Name;BMC Remote Access Service Point
IPMI Version;2.0
System GUID;4a34384f-c0c2-5280-3810-00304c4c4544
Number of Possible Active Sessions;5
Number of Current Active Sessions;0
LAN Enabled;No
SOL Enabled;Yes
IP Address Source;Static Address
IP Address;10.0.0.23
IP Subnet;255.255.255.0
IP Gateway;10.0.0.2
MAC Address;00-22-19-C8-5E-4E
DRAC
Attribute;Value
Product;Dell Remote Access Controller 5
Description;This system component provides a complete set of remote management functions for Dell PowerEdge servers
Version;1.45 (Build "09.01.16")
IP Address;10.0.0.23
IP Subnet;255.255.255.0
IP Gateway;10.0.0.2
Remote Connect Interface;Launch the DRAC Web Interface
Some ideas?
Thank's in advance!
Emauele
P.s. Sorry for my English :S...
biersl
2 Posts
0
May 7th, 2009 00:00
Hi Emauele,
I have the same problem. On click the Link 'Launch the DRAC Web Interface' the browser doesn't find the site. With Telnet or SSH I don't have a connection. Could it be, that the services do not work on the DRAC card? Is it possible to change some settings at BIOS?
Greetings
Markus
Beri75
3 Posts
0
May 7th, 2009 00:00
Hi Markus,
I'm agree with you, seems network services don't run on OS embedded card.....And yes, through BIOS I've looking for some settings to manage this functionalities, but nothing I have found. So, I've called Italian support guy to have a solution, if they could solve my problem through some suggestions or tricks I'll post here.....
Greetings
Emanuele
Beri75
3 Posts
0
May 8th, 2009 09:00
...Bad news....the support guy did not solve my problem, the only solution was the substitution of the DRAC card....
Hi
Emanuele
jonghoju
1 Message
0
May 9th, 2009 09:00
Hi,
open "cmd.exe" and enter below command to soft reset the rac.
racadm racreset soft
...found this in the documentation
After one minute also, web interface worked again
Hope it helps.
biersl
2 Posts
0
May 11th, 2009 02:00
Hi jonghoju,
the command 'racadm racreset soft' or 'racadm racreset hard' takes no effect. The web interface page still cannot be found. Firefox-Message: 'The server at 10.199.20.20 is taking too long to respond.'
The command 'racadm getsysinfo' brings the following informations:
C:\Dokumente und Einstellungen\Administrator>racadm getsysinfo
RAC Information:
RAC Date/Time = Mon May 11 10:19:18 2009
Firmware Version = 1.33
Firmware Build = 08.03.10
Last Firmware Update = NA
Hardware Version = A02
Current IP Address = 10.199.20.20 (for example)
Current IP Gateway = 10.199.20.1
Current IP Netmask = 255.255.255.0
DHCP Enabled = 0
MAC Address = 00:aa:cc:bb:aa:11 (for example)
Current DNS Server 1 = 0.0.0.0
Current DNS Server 2 = 0.0.0.0
DNS Servers from DHCP = 0
Register DNS RAC Name = 0
DNS RAC Name = rac-3200003
Current DNS Domain =
System Information:
System Model = PowerEdge 1950
System BIOS Version = 2.2.6
BMC Firmware Version = 01.97
Service Tag = 3200003
Host Name = hostname1
OS Name = Microsoft Windows Server 2003, Standard Edition
Power Status = ON
Watchdog Information:
Recovery Action = None
Present countdown value = 0 seconds
Initial countdown value = 0 seconds
Do you have any other ideas?
Greetings,
Markus