Storage, Drives & Media
Troubleshooting for Dell electronics including Monitors
Posts
Unsolved
This post is more than 5 years old
5 Posts
0
77482
July 14th, 2003 17:00
boot error - F1 to retry reboot, F2 for setup
1 person also has this problem
Responses(17)
No Events found!
swallowtail88
5 Posts
0
July 14th, 2003 17:00
Sorry about the empty post.
I am having problems with my hard drive. I have seen others post with similar problems; I am trying to start a new discussion thread here. Anyone who has experienced these same problems, please post and let us know what you have done and if you are still having the problem. I want to figure this thing out!
Dimsension 4300 purchased 9/01 running Windows ME, Maxtor 40GB hard drive, BIOS A02
This problem occurs upon power up, when I hear two beeps followed by the message:
Strike F1 to retry reboot; F2 for setup utility
When I go into setup, I see the following:
Primary Drive 0 Unknown Device (my hard drive)
Primary Drive 1 Off
Secondary Drive 0 Unknown Device (a CD-RW)
Secondary Drive 1 Off
Usually, all it takes is a power off/power on to get the computer to boot. Eventually, though it won't boot at all, so I have to reseat the cables to the hard drive - at the hard drive and at the motherboard (I've done this 3 times starting Jan 03). Then everything works. Just today when it wouldn't boot, I jiggled the power cord to the hard drive - didn't take it completely out and voila! everything works (didn't touch the IDE cable). What is this problem? It is so intermittent that I can't mess around with it a lot - the last time I reseated the cables was a month ago. And it is annoying.
I have also run scandisk, defrag, full computer virus scan, dell diagnostics - all OK.
I have also had problems coming out of hiberation and standby (I assume it can't wake the hdd). And while the computer was idle, I came back to find the message:
Primary hard disk drive 0 failure
Press the F1 key to continue, F2 to run setup
This only happened once.
Please share your stories - if ANYONE has made this go away, I would love to hear about it.
ceri sheeran
1.7K Posts
0
July 14th, 2003 18:00
Hi,
Try a new IDE cable and also connect the hard disk up to a different power connector.
Hibernation and standby are intended only for laptops, desktops can have problems when trying to use these. If you need power managment then use the monitor off and hard disk shut down features.
The hard disk waring messages give serious cause for concern indicating possible hard disk failure coming up. Back up all data on the hard disk not already saved on another source ( or two ) as soon as you can.
Then run the Dell hard disk diagnostics and phone Dell regarding a replacement drive.
hth
Ceri
jaystarter
5 Posts
0
July 18th, 2003 19:00
I had the same warning message 2 weeks ago, but for some reason everything seems ok now. Does this mean my HDD is still likely to fail? And where do I find the Dell Diagnostics disk?.
Dimension 4300. pent 4 . 1.7 128 ram . maxtor 5TO60H6. XPhome SP1
redberri
7 Posts
0
July 19th, 2003 02:00
swallowtail88
5 Posts
0
July 19th, 2003 18:00
jaystarter-
I have been receiving this error msg ever since I purchased my computer in Nov '01. My hard drive has yet to fail. I really don't think the drive itself is going to fail - but there is something screwy going on that I have yet to figure out. I will get this msg intermittently when all I have to do is power off/power on and it goes away. Eventually, though it doesn't go away and that is when I have reseated the IDE cables.
The Dell Diagnostics disk came with my computer. I had to set the BIOS up to boot from a CD instead of the hard drive. Follow the menu options to run diagnostics.
Good luck and let us know if this goes away for you and what you did.
swallowtail88
swallowtail88
5 Posts
0
July 19th, 2003 18:00
Dell diagnostics are actually found on the Dell Dimension Resource CD - oops
jaystarter
5 Posts
0
July 20th, 2003 09:00
-Xstinguish-
22 Posts
0
July 20th, 2003 18:00
Previously working as a Dell Technician. Here is what we did to resolve the issue.
-Strip all the PCI cards from the system.
-Unlplug all IDE cables. (cdrom, hard drive, etc.)
-Power system up. Clear NVRAM/Reset defaults in BIOS (Clear NVRAM using ALT-E and ALT-F on a 4300 while in system setup/BIOS.. Caps Lock, Num Lock and Scroll lock all must be turned on.)
-After clearing NVRAM/Resetting defaults. Power system down. Plug in only the hard drive. Reboot system. Let hard drive be detected automatically. Other devices will not be detected. Go back into BIOS. Clear NVRAM/Reset defaults.
-Power system back down. Plug in cdrom, let it detect with hard drive. (should see performing automatic IDE configuration)
-Basically what it amounts to is plugging in only one IDE device at a time and clearing NVRAM/Resetting defaults after each item is plugged in.
Im not exactly sure how long this lasted. I know it worked effectively and it was the way we were required to perform it. However, if it reoccurs within a month or two.. That I couldn't tell ya.
Also if you want to check the hard drive functionality -the easiest and most backed by Dell process is to run a 90/90. The drive has to be detected in BIOS in order to work effectively. If it is detected, you should be able to hit Control-Alt-D (at the same time) during post or right as you see the Dell splash. This will take you to a black screen and show -performing automatic IDE diagnostics. It will take a few minutes depending on drive size. It will return a pass / fail on the screen after complete. If there is a failure it will give a return code. In that instance you know what needs to be done next.
Message Edited by -Xstinguish- on 07-20-2003 01:20 PM
swallowtail88
5 Posts
0
July 21st, 2003 20:00
Xstinguish-
Thank you for your post! So from what you said I assume this is a *known* problem? Dell tech support had me both clear NVRAM and reseat the IDE cables, but not as you describe it. I will only hope that this will provide me with a permanent solution, because I do not think there is anything wrong with my hdd, my IDE cables, etc.
The part about the PCI cards. Do I just take them out, then perform all the magic with the IDE devices, then put them back in? What part do they play?
Thanks again
jaystarter-
You mention the part about the two beeps and memory. Yes, in my documentation it says that "memory parity cannot be reset." A little misleading, I think. If you ever get this message again (God forbid), check the diagnostic lights on the back of your computer. Mine were YGGY which means "IDE bus failure has occurred." More to the point.
jaystarter
5 Posts
0
July 22nd, 2003 11:00
jaystarter
5 Posts
0
July 22nd, 2003 11:00
redberri
7 Posts
0
August 2nd, 2003 23:00
I had the same situation with the diagnostic lights on the back of computer. First YGGY, and then it changed to GGGY. What do you do about this problem?
redberri
7 Posts
0
August 2nd, 2003 23:00
I have Dell Dimension 82 with WinXP Professional OS.
DELL-Karell
2.5K Posts
0
August 4th, 2003 14:00
To All,
Thank you for using the Dell Community Forum.
If you get the following error message,"Strike F1 to retry reboot; F2 for setup utility",
here are the troubleshooting steps you need to take.
1.Remove and reseat both the IDE and Power cables to the Hard Drive.
2.Remove and reseat both the IDE and Power cables to all other IDE drives.
3.Remove and reseat the IDE cables to the motherboard.
4.Clear NVRAM and reset your bios defaults.
5.Upgrade to the latest bios files.
6.Run the Dell 9090 Diagnostics to test the HD and see if it has actually failed.
7.Swap out IDE cables with your CDROM drive to see if the IDE cable is bad.
8.Swap out IDE controllers to see if the controller on the motherboard is bad.
9.Try another Hard Drive to verify whether your drive has failed or not.
How Do I Restore Setup Defaults On My Dell™ Dimension™ System?
How Do I Clear NVRAM on my Dell™ Dimension™ System?<ADMIN NOTE: Broken link has been removed / replaced from this post by Dell>
Why is my Dell™ Dimension™ or OptiPlex™ system unable to recognize my hard drive or CD drive?
how do i run 90-90 hard drive diagnostics (dell hard drive confidence test utility) on dell™ optiplex™ and dimension™ computers?
jaystarter
5 Posts
0
August 11th, 2003 18:00