Announcement Banner
UNSOLVED

cg1245

updated

11 years ago

C

cg1245

6 Posts

0

69153

May 12th, 2015 18:00

T110 No display

Hello, I have a poweredge t110 and the display won't work. I had this computer for about a year and it worked perfectly two days before it broke. I took the graphics card out, which is an xfx r5 230. I plugged it into the builtin vga port and turn it on and nothing happened. A month ago I had a problem with graphics cards, it seems that the faster the card you have, the slower the computer is. I took the cmos battery out then put it back in and nothing happened. I also noticed that the 1 light is constant on the front of the computer. I'm wondering if there is something with the bios? I don't know, help!

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    4721

    0

    Posted May 13th, 2015 08:00

    CG1245,

    I would say from your description that the card isn't working in that slot. I would suggest that you take the server to a Minimum to Post configuration. That is removing everything from the server except the following;

    • CPU.
    • Heatsink for CPU for prevention of over-heating.
    • System Board.
    • PSU.
    • Front panel (to power system ON).
    • 1 DIMM for CPU. 

    That includes removing the graphics card as well. After removing everything, but prior to powering up, locate this jumper (shown below) and move the NVRAM_CLR jumper over.

    Power up the server, when you see lights power down and restore the jumper to its original location. Power up completely after that. 

    Plug the monitor to the embedded VGA port on the rear of the server.

    Let me know if you are getting video or not.

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • cg1245

    6 Posts

    4739

    0

    Posted May 14th, 2015 19:00

    Still no luck with it. I also noticed that there is two jumpers, do I only use one?

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    4739

    0

    Posted May 15th, 2015 05:00

    Yes, only move the NVRam_Clr one over. When you power the server, what are the 4 diagnostic LED's showing?

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • cg1245

    6 Posts

    4739

    0

    Posted May 15th, 2015 10:00

    Also I had a no display problem before, and all I did to fix it was to replace the cmos battery

  • cg1245

    6 Posts

    4739

    0

    Posted May 15th, 2015 10:00

    It only shows a 1 on the front.

    I saw the 4 flash for about a second before the 1 came up

    I also saw that the lights flash 3 and 4 then a 1 when the jumpers are back in their normal position.

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    4739

    0

    Posted May 15th, 2015 11:00

    CG1245,

    The server going to just a lone 1 on the diagnostics indicates an issue with the memory, specifically that No memory modules were detected. Could you test each dimm individually in slot 1. Now if the server is showing 1,3, and 4, all at the same time then it is an indication of a system board hardware failure. Could you clarify if they all show or if the 3 and 4 drop of and leave 1 alone.

    Thanks.

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • cg1245

    6 Posts

    4739

    0

    Posted May 15th, 2015 13:00

    I noticed that it flashes 1 3 and 4 at the same time, so it is the motherboard? I also tried new ram in it and there's still a 1

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    4739

    0

    Posted May 18th, 2015 07:00

    It does look like an issue with the motherboard. Do you happen to have another matching system we could test the components of this server with?

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • cg1245

    6 Posts

    4739

    0

    Posted May 19th, 2015 18:00

    No I do not have any other poweredges.

  • ismokealot

    1 Rookie

    •

    3 Posts

    1099

    0

    Posted June 2nd, 2015 18:00

    To the flash i was trying to post this from a iphone anyhow that thing did mess up some stuff for me. I fixed the display issue my main problem i was having is trying to install windows 7 on this computer. I eventually some how did something in the bios and it worked. Before it wouldn't show the 2 hard drives that were in the computer. I need help setting the bios to boot windows 7. I have some how managed to install it from a USB. I just need to know what the bios setting should be should it boot from bios or uefi right now it is set to bios. I never had a server before i don't know what is the difference between this and a normal desktop except server has some better hardware and more hard drive bays. Basically what i am asking is how do i configure the bios so it stops showing me these commands for things and just boots into windows 7 quickly. During the install process i deleted one of the drives from the windows 7 setup screen and it would not show up once the windows was installed i physically removed it since i don't need that much space anyways but i am not sure why it doesn't show up. Would be nice to know. I am going to download the Server 2008 drivers for this pc and go from there i will make a brand new post about this subject. The jumper trick worked for me and i was able to install windows 7 once i switched the drive from raid to ahci