you do not want to present metas to Celerra and second thing you do not want to expand device already presented to Celerra (create metas). So let's say you need to create a 100G file system for a new project. Your hyper size on the array is around 50G so you will need to map two hypers to FAs used by Celerra. You will map starting at LUN address 11 and then 12. Once mapping is complete, rescan on the Celerra side. Run nas_disk -l and you should see your two hypers listed at the bottom of the list. Now try to create your file system.
Tony ..where did you see this requirement ? I have FAs from DMX2000 and DMX3 and my devices are only using LUN id ..TID is not used at all (set to 0). My LUN addresses start from 001, 000 is VCM.
The Celerra reserves LUN ID from 000-00F for the DART code and others. When using the DMX you need to start with LUN ID 010 for data luns. Same holds true for CLARiiON arrays. When you present a data LUN, the HLU needs to start at 16 or higher as the Dart code reserves the lower luns.
The Celerra reserves LUN ID from 000-00F for the DART code and others. When using the DMX you need to start with LUN ID 010 for data luns.
i see ..this applies for DMX you are booting off, if you have additional DMX ..its LUNs can be mapped to LUN address 0 and up. Thanks for clarification Tony.
do not use Lun 00 to 0F even on a second DMX. Then there would be no way, the datamover would try to boot from the wrong DMX. Even with cleared binding tables.
my second DMX has been in production for 2 years now ..so it will be hard to re-do it now. Can you point to any documentation that explains how to provision DMX storage to Celerra gateway ? I have always seen instructions for Clariion ..but never for DMX.
Sorry my friend - the Celerra Procedure Generator is for EMC internal use only - mainly for Customer Support activities. Unlike CLARiiON procedure Generator, it does not help much on the configuration or implementation part. Also there is no Customer version for this unlike CLARiiON Procedure generator. Sorry again not to help you this time Sandip
dynamox
9 Legend
•
20.4K Posts
0
October 30th, 2008 04:00
sagle
90 Posts
0
October 24th, 2008 11:00
dynamox
9 Legend
•
20.4K Posts
0
October 24th, 2008 11:00
tonydcdi-ymiT1
70 Posts
0
October 24th, 2008 15:00
Message was edited by:
tonydcdi
dynamox
9 Legend
•
20.4K Posts
0
October 24th, 2008 18:00
vincec1
16 Posts
0
October 26th, 2008 22:00
How can i check is the hyper set to CELERRA_FBA emulation ?
The device i have map to the FA port only comes with LUN number, what is TID?
dynamox
9 Legend
•
20.4K Posts
0
October 27th, 2008 03:00
symdev show -sid hyper#
and look for device emulation field.
TID is target id, as far as i know it's only used with FA that have Volume set Addressing enabled for HPUX.
Here is a thread that explains how to provision space from DMX to Celerra gateway.
http://forums.emc.com/forums/thread.jspa?messageID=594750
tonydcdi-ymiT1
70 Posts
0
October 27th, 2008 18:00
dynamox
9 Legend
•
20.4K Posts
0
October 27th, 2008 18:00
DART code and others. When using the DMX you need to
start with LUN ID 010 for data luns.
i see ..this applies for DMX you are booting off, if you have additional DMX ..its LUNs can be mapped to LUN address 0 and up. Thanks for clarification Tony.
Peter_EMC
674 Posts
0
October 28th, 2008 08:00
do not use Lun 00 to 0F even on a second DMX. Then there would be no way, the datamover would try to boot from the wrong DMX. Even with cleared binding tables.
dynamox
9 Legend
•
20.4K Posts
0
October 28th, 2008 10:00
my second DMX has been in production for 2 years now ..so it will be hard to re-do it now. Can you point to any documentation that explains how to provision DMX storage to Celerra gateway ? I have always seen instructions for Clariion ..but never for DMX.
Thanks
dynamox
9 Legend
•
20.4K Posts
0
October 28th, 2008 13:00
dynamox
9 Legend
•
20.4K Posts
0
October 28th, 2008 13:00
Home > Support > Product and Diagnostic Tools > Celerra Tools
nandas
4 Operator
•
1.5K Posts
0
October 28th, 2008 13:00
Sorry again not to help you this time
Sandip
tonydcdi-ymiT1
70 Posts
0
October 28th, 2008 13:00
Most of the docs that I use are internal EMC docs as I am an ASN partner, however, have you tried the Customer Celerra Procedure Generator?