Unsolved
This post is more than 5 years old
1 Message
0
1204
July 11th, 2008 20:00
Brocade 5000 vs McData 4700 ISL problems
Hi all
I faced a critical issue on ISL between Brocade 5000 and McData 4700
The background as below
-----------------------------------------------------------------
McData 4700 firmware 9.3.1, Domain ID#1 , interop Mode :1 (Existing switch with zoning)
Brocade 5000 firmware :5.3.X, Domain ID#99, Interop Mode: 1 (Fresh install)
--------------------------------------------------------------------
A Fiber was plugged between two switch
Both of their connection ports were shown as E-Port
In Brocade 5000 web GUI, i can see two switches (Domain ID #97 & #99)
Since the Domain #97 is equal to McData Domain #1
1) The switch with Domain#97 cannot be extended when i double click, that means i cannot see the port of McData in Brocade Web GUI.
2) None zoning from McData can be seen on Brocade Web GUI, but all WWN from McData can be found.
3) The Zone Config of McData cannot be found on Brocade.
4) In case, i enter the brocade via TELNET. All zoning of McData can be seen by typing "zoneshow"..
In McData Web GUI.
It shows the McData port only, no port of Brocade 5000 can be found
i wonder why i can;t find the zoning on web GUI but on telnet. Is the ISL procedure incomplete.?
Anyone faced the similar issue?
Thank you very much
Ryan LI
I faced a critical issue on ISL between Brocade 5000 and McData 4700
The background as below
-----------------------------------------------------------------
McData 4700 firmware 9.3.1, Domain ID#1 , interop Mode :1 (Existing switch with zoning)
Brocade 5000 firmware :5.3.X, Domain ID#99, Interop Mode: 1 (Fresh install)
--------------------------------------------------------------------
A Fiber was plugged between two switch
Both of their connection ports were shown as E-Port
In Brocade 5000 web GUI, i can see two switches (Domain ID #97 & #99)
Since the Domain #97 is equal to McData Domain #1
1) The switch with Domain#97 cannot be extended when i double click, that means i cannot see the port of McData in Brocade Web GUI.
2) None zoning from McData can be seen on Brocade Web GUI, but all WWN from McData can be found.
3) The Zone Config of McData cannot be found on Brocade.
4) In case, i enter the brocade via TELNET. All zoning of McData can be seen by typing "zoneshow"..
In McData Web GUI.
It shows the McData port only, no port of Brocade 5000 can be found
i wonder why i can;t find the zoning on web GUI but on telnet. Is the ISL procedure incomplete.?
Anyone faced the similar issue?
Thank you very much
Ryan LI
No Events found!
RRR
6 Operator
•
5.7K Posts
0
July 14th, 2008 00:00
dynamox
11 Legend
•
20.4K Posts
•
87.4K Points
0
July 14th, 2008 09:00
http://forums.emc.com/forums/thread.jspa?threadID=48632&tstart=150
Ew5njQlc1112553
1 Message
0
September 7th, 2010 12:00
Hi,
Is there a fix for Brocade 5000 and McData 4700 ISL problem?
Thanks,
dynamox
11 Legend
•
20.4K Posts
•
87.4K Points
0
October 14th, 2010 14:00
what is it exactly that you are trying to do ? Connect both together or simply migrate systems from one to another ?
dynamox
11 Legend
•
20.4K Posts
•
87.4K Points
0
October 15th, 2010 05:00
so you can either connect Brocade and McData together (you have to make sure interop settings are set properly so both vendor switches can talk to each other) and slowly move systems/storage to new switch or do a cutover and swing systems/storage from one switch to the other.