Problem with my dell laptop while starting

Hi supernova1989,

I would suggest you to update the BIOS on the system. Please enter your service tag # on the link below, select the operating system, and then download the BIOS from the BIOS section for issue resolution.

http://dell.to/ZaQuel

In addition, I would suggest that you run the diagnostics on the computer by following the steps mentioned below and check if there is any issue with the hardware on your system.

1. Turn on or restart the computer.
2. Immediately at the Dell logo screen, starting tapping the key once a second until the One Time Boot menu appears (if the computer boots to Windows turn the computer off and try again).
3. At the One Time Boot menu, press the arrow key to highlight Diagnostics, PSA+ or Enter ePSA, then press to begin the hardware Diagnostics.
4. Write down any error codes listed. Reply to us with the error codes.

Please let me know if this helps.

Hi Ravi,

Thanks for help. Problem is now solved following your ways.

Hi shihab91,

I am sorry about the situation; please send me the snap shot of the error message. Also let me know if the BIOS is updated?

I have same prolem.
I tried on your way but NOT SOLVED.

In Diagnostic - there is no error.(all pass)

PLEASE WHAT SHOULD I DO...

I have Dell inspiron n4050

core i3

ram 2gb

i am in same problem. i have already accomplished that procedure but my problem not solved at all. please response to my problem. 

Hi nomancste,

I am sorry about the inconvience; please send me the snap shot of the error message

When I press the power button, nothing happen unless i press any key. If I press any key, I get the following message:

boot drive=80, Not CD

get_cdinfo(81), int13/4B01(81), err=1, drive=81, cdrom_drive == FFFFFFFF.

Open/default...

Warning: MBR cylinders (1024) is not equal to the BIOS one(1023).

Warning: MBR total sector (976771072) is greater than the BIOS one (16434495). Some buggy BIOS could hang when you access sectors exceeding the BIOS limit.
failure.


End of menu init commands. Press any key to enter command-line or run menu.....

---------------------

Then it starts the windows.

Hi nomancste,

Thanks for the information, try running the hardware diagnostics by tapping the F12 key on a few times during startup until you see the ‘One Time Boot Menu’ appear.

At the one time boot menu, press the down arrow key to highlight ‘Diagnostics’, and then press Enter to begin the hardware diagnostics.

If the test fails, please make a note of any error codes listed. You can also refer to the link below. 

http://dell.to/162eS7m

Let me know about the progress.

Diagnostics has all test passed and i have update BIOS but the problem is  still remaining .

Hi nomancste,

Please send me the system service tag or express service code through a private chat, I will see what best can be done.

Click on my username select start a private conversation and send me the details. Please refer to the link below where to locate the service tag or express service code.

http://dell.to/162b3za

Let me know about the progress

i have this problem too and after i do follow your step the error occur

Error code : 2000-0333

validation 40420

I have same problem but my error codes:

boot drive=80, Not CD

get_cdinfo(81), int13/4B01(81), err=1, drive=81, cdrom_drive == FFFFFFFF.


End of menu init commands. Press any key to enter command-line or run menu.....                                     

I try to do follow you but it's not solved!

I have been using Dell Inspiron n4050 for about 1 year 2 months. I had to face blue screen error after using 3 months and that problem was solved after re installing windows. Now I have to face the following problem while starting it:

When I press the power button, nothing happen unless i press any key. If I press any key, I get the following message:

boot drive=80, Not CD

get_cdinfo(81), int13/4B01(81), err=1, drive=81, cdrom_drive == FFFFFFFF.

Open/default...

Warning: MBR cylinders (1024) is not equal to the BIOS one(1023).

Warning: MBR total sector (976771072) is greater than the BIOS one (16434495). Some buggy BIOS could hang when you access sectors exceeding the BIOS limit.
failure.


End of menu init commands. Press any key to enter command-line or run menu.....

---------------------

Then it starts the windows. I re install the windows but problem isn't solved. I can't start windows without pressing any key. 

Please can anyone help me regarding this issue? What are the problems? How can I get solved this?

Laptop Details:

Processor: Intel (R) Core(TM) i3-2350M CPU @ 2.30GHz 2.30GHz

RAM: 2 GB

System Type: 32 bit operating system

HDD: 500 GB

Operating System: Windows 7 Ultimate

After hardware Diagnostics , Result is Hard Drive Error . And show this massege. this message is given bellow :-

Error Code 2000-0151

Validation 41437

Meg: Hard Drive 0 - S/N WD-WXG1A3122538, incorrect status = 3E

No additional sence information

error code is 2000-0142 now plz tell what should i do?