Jukebox error: Illegal Request, Logical Unit Not Ready, Error

Question

Hello All,
We are getting following error while jbverify.
-----------------------------------------------------------------------------------------------------------------------
C:\Documents and Settings\administrator.E1LSP>jbverify
Jbverify is running on host sc14lbar
no enabled stand alone devices found.
Processing jukebox devices...
Processing jukebox jb:
Testing drive 1 (\\.\Tape0) of JB jbjbverify: Jukebox error: Illegal Request, L
ogical Unit Not Ready, Initialization Command Required
jbverify: Jukebox error: Illegal Request, Logical Unit Not Ready, Initialization
Command Required
jbverify: Jukebox error: Illegal Request, Logical Unit Not Ready, Initialization
Command Required
jbverify: Jukebox error: Illegal Request, Logical Unit Not Ready, Initialization
Command Required
jbverify: Jukebox error: Illegal Request, Logical Unit Not Ready, Initialization
Command Required
-----------------------------------------------------------------------------------------------------------------------
output of inquire command
-----------------------------------------------------------------------------------------------------------------------
C:\Documents and Settings\administrator.E1LSP>inquire
Could not start a Removable Storage session (0x00000422).
scsidev@2.0.0:HL-DT-STDVDRAM GSA-T50N RW06|CD-ROM
scsidev@4.0.0:FUJITSU MBB2147RC 5204|Disk, \\.\PHYSICALDRIVE0
S/N: BS04P9405MH0
WWNN:500000E110035E50
WWPN:500000E110035E52
PORT:00000001
scsidev@5.0.0:HP Ultrium 3-SCSI C24B|Tape, \\.\Tape0
S/N: HU108211NN
ATPN:HP Ultrium 3-SCSI HU108211
NN
WWNN:5000E11129AD7001
WWPN:50060B00007FD004
PORT:00000001
scsidev@5.0.1:FSC FibreCAT-TX24 S24.32|Autochanger (Jukebox)
S/N: TXDE65404196_LL0
ATNN:FSC FibreCAT-TX24 S2TXDE6540
4196_LL0
PORT:00000001
-----------------------------------------------------------------------------------------------------------------------
Even though jbconfig is successful but after inventory, networker is not able to identify the tape.

Any clue ?

Regards
Hemant

DavidHampson · Answer

I would check first of all the jukebox has been enabled and is in a ready state...

Hormigo · Answer

The Service Removable Storage is unable?

Hemant-I97jT · Answer

Hello David, Thanks for your response.The jukebox is in ready state.With RegardsHemant.

DavidHampson · Answer

What kind of jukebox do you have? If I remember rightly jbverify is only supported with a small number of jukeboxes... And what do you wish to achieve - I don't recall ever using the command in the 10 years I have been working with Networker...

Hemant-I97jT · Answer

Hello Hormigo, Thanks for your response.We are not using the Removable Storage service. Hence disabled.RegardsHemant

DavidHampson · Answer

Perhaps I am wrong with it only being supported on just some jukeboxes. Can you let us know what jukebox you have and if the output is the same now you have clarified that the jukebox and drives are enabled..

Hemant-I97jT · Answer

Hello David Hampson,
Thanks for your response.

From Networker documentation:
"jbverify verifies the devices defined in the NetWorker database, making sure that each
one of them is configured properly by checking them for accessibility and usability.".

We are using TX-24 S2 (LTO 3 type) jukebox. The Jukebox and drives are enabled.

any clue ?

Thanks
With Regards
Hemant.

DavidHampson · Answer

Is the jbverify output the same?

ble1 · Answer

In past 10 years I have tried jbverify 3 times; each of them it failed while everything else was working fine. So, I do not tend to use that command at all. With that in mind, and the fact that you say everything else works, I would suggest to test manually load and unload and forget jbverify.

mpn1 · Answer

Hi,Does the Library front panel shows any errors / comments.Did u tried rebooting the Library as well as restartgint he Networker application. Works for me..You may try nsrjb -IEv, so that the Library is initialized as well as inventoried by Networker... might help

cameron11 · Answer

Hi,For a sanity check I looked at the Hardware Compatibility Guide:http://powerlink.emc.com/km/live1/en_US/Offering_Technical/Technical_Documentation/NetWorker_HCG.pdfBased on What I see there, the FibreCat TX24 is only supported on the following OS:Windows 2003, x64I reviewed the previous posts and it is not clear which version of Windows you have.

NetWorker

Jukebox error: Illegal Request, Logical Unit Not Ready, Error

Was this post helpful?