please help me to do inventory on this storage node.

Question

if we run nsrjb command it is detecting, i.e., HP@9.1.0, if we run nsrjb -Iv it is not detecting, if we run inquire command it is showing and in GUI mode it is not showning any error message, we power cycle this library twice.

Please do the needful how to do inventory on this.

C:\>nsrjb
No jukebox selected.
1: HP@9.1.0
2: rd=bepuuarp:COMPAQ@4.1.0
3: rd=bepuugho:COMPAQ@5.0.0
4: rd=puuemaapp02:HP@9.0.1
Please select a jukebox to use:? [1] 1

Jukebox HP@9.1.0: (Not ready to accept commands)
slot volume pool barcode volume id recyclable
1: LTO093(R) Default LTO093 3242443431 no
2: LTO326(R) Default LTO326 376198379 yes
3: LTO138(R) Default LTO138 4234270839 yes
4: LTO407(R) Default LTO407 3997512954 no
5: LTO370(R) Default LTO370 3751100072 yes
6: LTO129(R) Default LTO129 4014307624 no
7: LTO185(R) Default LTO185 1702911995 yes
8: LTO272(R) Default LTO272 2336586434 no
9: LTO357(R) Default LTO357 4001834160 yes
10: LTO059(R) Default LTO059 3567571325 yes
11: LTO279(R) Default LTO279 2149624761 no
12: LTO090(R) Default LTO090 159650846 yes
13: LTO224(R) Default LTO224 1203641342 no
14: LTO282(R) Default LTO282 1019093014 no
15: -* LTO183 -
16: LTO196(R) Default LTO196 1186864300 no
17: LTO064(R) Default LTO064 4047845326 no
18: LTO278(R) Default LTO278 1052647274 no
19: LTO127(R) Default LTO127 800385603 no
20: LTO253(R) Default LTO253 4536218 no
21: -* LTO182 -
22: LTO446(R) Default LTO446 3722380969 no
23: LTO083(R) Default LTO083 3941955368 no
24: LTO448(R) Default LTO448 4192070042 no
25: LTO270(R) Default LTO270 4218715841 yes
26: LTO214(R) Default LTO214 1086201530 no
27: LTO220(R) Default LTO220 1170087258 no
28: LTO200(R) Default LTO200 4081584845 no
*not registered in the NetWorker media data base

drive 1 (\\.\Tape0) slot 1: LTO093
drive 2 (\\.\Tape1) slot :

C:\>nsrjb -Iv
setting verbosity level to `1'
No jukebox selected.
1: rd=bepuuarp:COMPAQ@4.1.0
2: rd=bepuugho:COMPAQ@5.0.0
3: rd=puuemaapp02:HP@9.0.1
Please select a jukebox to use:? [1]

DavidHampson · Accepted Answer

You didn't read my response just entered the command the same as before - the jukebox name is case sensitive - put the command in how I wrote it and it should work.

ble1 · Answer

Well, it's says that is not ready... verify the control path and if it is correct one simply disable and enable jukebox and see if you get jukebox ready after that (it may take few minutes sometimes).

DavidHampson · Answer

Either your jukebox is not enabled or it is not in a ready state - verify it is enabled, if so check the daemon.log for 'jukebox is ready' message a short time (few minutes) after 'jukebox is enabled' message...

changalrai · Answer

we did disable after some time enable also, but again it is it is not detecting to inventory.

ble1 · Answer

But is your library ready? If it is not, you no nsrjb operation will work. If it is not, then you musct check your library first. I do not trust the names do first check for that library under properties what does it say for control path.

Then test that path with sjirdtag command.

DavidHampson · Answer

An enabled library is not necessarily a ready library - did you check the library was ready?

changalrai · Answer

after enable also we are not able to do inventory, we check that it is enable,

DavidHampson · Answer

runnsrjb -j jukeboxname -Ivvvvfrom the command line and post the output here

changalrai · Answer

i got this error message.C:\Documents and Settings\apcxov-reddyc02>nsrjb -j rd=bepuuarp:compaq@4.1.0 -Ivvvvsetting verbosity level to `4'39078:nsrjb: RAP error: No jukebox by that name exists in the NetWorker configuration.

DavidHampson · Answer

Try this command:nsrjb -j rd=bepuuarp:COMPAQ@4.1.0 -Ivvvv

changalrai · Answer

C:\Documents and Settings\apcxov-reddyc02>nsrjb -j rd=bepuuarp:compaq@4.1.0 -Ivvvvsetting verbosity level to `4'39078:nsrjb: RAP error: No jukebox by that name exists in the NetWorker configuration

changalrai · Answer

thanks David Hampson,now its working, once again thank you so much,

NetWorker

please help me to do inventory on this storage node.

Was this post helpful?