1 Rookie
•
4 Posts
0
38
Ethernet 1/1/17 is up, line protocol is down with SFP 10G OS10
Hello All,
Please I need you assitance if anyone had the same situation.
I have plugged one Huawei (CE 5855-48) SFP 10G on the switch (Dell s5224F-ON), the problem is : the dell switch always showing that the Pluggable media present, SFP28 type is SFP28 25GBASE-SR-AOC,and the line protocol is down.
If we plug a Dell s5224F-ON SFP 10G into another switch Dell s5224F-ON, we have (the line protocol is up)
If we try to configure the Auto-Negotiation to Off or Auto, we have the same result (the line protocol is down)
Here is the show interface result :
OS10# show interface ethernet 1/1/7
Ethernet 1/1/7 is up, line protocol is down
Hardware is Eth, address is c4:5a:b1:75:ad:0c
Current address is c4:5a:b1:75:ad:0c
Pluggable media present, SFP28 type is SFP28 25GBASE-SR-AOC
Wavelength is 850
Interface index is 21
Internet address is not set
Mode of IPv4 Address Assignment: not set
Interface IPv6 oper status: Disabled
MTU 1532 bytes, IP MTU 1500 bytes
LineSpeed 0, Auto-Negotiation on
Configured FEC is cl108-rs, Negotiated FEC is off
Flowcontrol rx off tx off
ARP type: ARPA, ARP Timeout: 60
Tag Protocol IDentifier (TPID) value: 0x8100
Last clearing of "show interface" counters: 04:57:28
Queuing strategy: fifo
Input statistics:
0 packets, 0 octets
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts, 0 Unicasts
0 runts, 0 giants, 0 throttles
0 CRC, 0 overrun, 0 discarded
Output statistics:
0 packets, 0 octets
0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
0 Multicasts, 0 Broadcasts, 0 Unicasts
0 throttles, 0 discarded, 0 Collisions, wred drops
Rate Info(interval 30 seconds):
Input 0 Mbits/sec, 0 packets/sec, 0% of line rate
Output 0 Mbits/sec, 0 packets/sec, 0% of line rate
Time since last interface status change: 04:57:29
rikazkhan
1 Rookie
1 Rookie
•
4 Posts
1
April 21st, 2024 14:33
It sounds like you're receiving a status message from a network device, indicating that Ethernet interface 1/1/17 is physically connected (up), but the line protocol is not active (down). Additionally, it seems to be utilizing a 10 Gigabit Ethernet SFP (Small Form-factor Pluggable) module running on OS10, which likely refers to the operating system running on the networking equipment.
DELL-Young E
Moderator
Moderator
•
3.6K Posts
1
April 22nd, 2024 03:50
Dell switch 25G port speed is converted to 10G then only can connect with 10G of Huawei
This may help:
https://dell.to/4d4UxSi
DELL-Joey C
Moderator
Moderator
•
3.1K Posts
0
April 24th, 2024 02:33
Hi,
You can refer to this documentation to create link between the switches, but I'm unsure if both Huawei and S5224F configuration will be compatible. Please check the documentation and implement the configuration. Let us know how is the outcome.
https://dell.to/3vUUBU8
DELL-Joey C
Moderator
Moderator
•
3.1K Posts
0
April 24th, 2024 09:44
Hi,
If port group is configured, you will need to issue the command:
OS10(config)# interface ethernet 1/1/17:1
Diaw
1 Rookie
1 Rookie
•
4 Posts
0
April 23rd, 2024 21:51
Thanks for your feedback,
The protocol is up now with the following command :
OS10(config)# port-group 1/1/17
OS10(conf-pg-1/1/1)# mode Eth 10g-4x
I need your help to configure the link between switches (Fiber optic)
I have configured on the Huawei switch (port trunk / vlan / eth-Trunk) but I don't know the equivalent on Dell switch for the link
Please help us to configure the Dell switch for the communication between the switches
Diaw
1 Rookie
1 Rookie
•
4 Posts
0
April 24th, 2024 09:13
Hi,
Once the port group is configured, I no longer have access to the specific interface for the vlan and trunk configuration.
OS10(config)# interface ethernet 1/1/17
% Error: ethernet1/1/17 is not configurable
Diaw
1 Rookie
1 Rookie
•
4 Posts
0
April 24th, 2024 18:08
The link between the switches (Dell - Huawei) are OK
Thanks you for all