Unsolved
This post is more than 5 years old
9 Posts
0
23214
September 21st, 2012 09:00
Routing VLAN traffic on 6224 switch
Have 3 VLANs setup on a 6224 switch: 10,20 &99. Have 99 connected to our Sonicwall interface and have connectivity, the problem is routing traffic from VLAN 10 & 20 to 99. I have included the config below. Have tried creating a static route to our Sonicwall interface and even tried OSPF. Thks
!Current Configuration:
!System Description "PowerConnect 6224, 3.3.4.1, VxWorks 6.5"
!System Software Version 3.3.4.1
!Cut-through mode is configured as disabled
!
configure
vlan database
vlan 10,20,99
vlan routing 10 1
vlan routing 20 2
vlan routing 99 3
exit
stack
member 1 1
exit
ip address 192.168.2.1 255.255.255.0
ip routing
ip route 0.0.0.0 0.0.0.0 10.168.12.254
interface vlan 10
routing
ip address 192.168.3.1 255.255.255.0
exit
interface vlan 20
routing
ip address 192.168.4.1 255.255.255.0
exit
interface vlan 99
routing
ip address 10.168.12.1 255.255.255.0
exit
router ospf
router-id 172.1.1.1
no enable
exit
!
interface ethernet 1/g1
switchport access vlan 10
exit
!
interface ethernet 1/g2
switchport access vlan 10
exit
!
interface ethernet 1/g3
switchport access vlan 10
exit
!
interface ethernet 1/g4
switchport access vlan 10
exit
!
interface ethernet 1/g5
switchport access vlan 10
exit
!
interface ethernet 1/g6
switchport access vlan 10
exit
!
interface ethernet 1/g7
switchport access vlan 20
exit
!
interface ethernet 1/g8
switchport access vlan 20
exit
!
interface ethernet 1/g9
switchport access vlan 20
exit
!
interface ethernet 1/g10
switchport access vlan 20
exit
!
interface ethernet 1/g11
switchport access vlan 20
exit
!
interface ethernet 1/g12
switchport access vlan 20
exit
!
interface ethernet 1/g24
switchport access vlan 99
exit
exit
Route Codes: R - RIP Derived, O - OSPF Derived, C - Connected, S - Static
B - BGP Derived, IA - OSPF Inter Area
E1 - OSPF External Type 1, E2 - OSPF External Type 2
N1 - OSPF NSSA External Type 1, N2 - OSPF NSSA External Type 2
S 0.0.0.0/0 [1/0] via 10.168.12.254, vlan 99
C 10.168.12.0/24 [0/1] directly connected, vlan 99
C 192.168.3.0/24 [0/1] directly connected, vlan 10
C 192.168.4.0/24 [0/1] directly connected, vlan 20
VLAN Name Ports Type Authorization
----- --------------- ------------- ----- -------------
1 Default ch1-48, Default Required
1/g13-1/g23,
1/xg1-1/xg4
10 1/g1-1/g6 Static Required
20 1/g7-1/g12 Static Required
99 1/g24 Static Required
0 events found
WEBCCI
9 Posts
0
September 21st, 2012 09:00
Oddly we cannot ping between VLANs with Win7 clients but we can with XP. Have shutdown firewall service, etc.
The Sonicwall is a 3560 Pro which has 2 LAN interfaces and 2 WAN interfaces setup. Have VLAN 99 plugged into one of the LAN interfaces.
WEBCCI
9 Posts
0
September 21st, 2012 10:00
Actually it is a 3060 (typo in earlier post).
We have them set statically and pointed to their associated VLAN address as their GW.
Should we take out the static route from 99 to the sonicwall?
Will have to check if they can ping each other on the same VLAN, believe they can.
WEBCCI
9 Posts
0
September 25th, 2012 14:00
Not able to get out at all when we take the static out. We can get out on the 99 VLAN because of the static route, problem is we cannot get out from VLAN 10 & 20 maybe due to the different subnets? When 10 & 20 is routed through 99 via the static route do they keep their original IP so that maybe the Sonicwall doesn't know how to return the traffic without a static in the Sonicwall? In other words, the static route via VLAN 99 forwards the traffic and doesn't NAT it right?
WEBCCI
9 Posts
0
September 25th, 2012 15:00
Don't we need to create static routes in the Sonicwall so, it knows how to route traffic back from the 192.168.3.1 & 192.168.4.1 networks?
WEBCCI
9 Posts
0
September 26th, 2012 10:00
Thanks for the information. We changed to trunk mode, but still cannot get out from the 10 & 20 VLANs. Definitely think we need to enter static routes on the Sonicwall to provide return routes.