Hello.
A mandatory update for the SSD that is used in the switch has been released. Acted strictly according to the instructions RN_Innodisk_SSD_FW_Updater.pdf

the update was carried out from the NOS.

after the reboot command, the ssd firmware was not updated.
gave a second command to update, connected to a port and saw errors when loading after the grub.
below is how it looked in the terminal

# image install image://ssd-firmware-updater-3ie3-r0.3.00.7.0-1
.bin
Install started.
Use 'show image status' for updates
switch_name# show image status
Image Upgrade State: idle
==================================================
File Transfer State: idle
--------------------------------------------------
State Detail: No download information available
Task Start: 0000-00-00T00:00:00Z
Task End: 0000-00-00T00:00:00Z
Transfer Progress: 0 %
Transfer Bytes: 0 bytes
File Size: 0 bytes
Transfer Rate: 0 kbps

Installation State: install-success
--------------------------------------------------
State Detail: Completed: Success
Task Start: 2022-03-05T08:33:57Z
Task End: 2022-03-05T08:33:58Z
switch_name# reload

Proceed to reboot the system? [confirm yes/no]:yes
Session terminated for user admin on console
[ OK ] Stopped System Logger Daemon.
Stopping Advanced key-value store...
[ OK ] Stopped Serial Getty on ttyS0.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Stopped Advanced key-value store.
[63967.287814] sysrq: SysRq : Emergency Remount R/O
[63967.404347] Emergency Remount complete
15, 00068001, 19, 00068000,

BIOS Boot Selector for S4100
Version 3.33.0.1-11

POST Configuration
CPU Signature 406D8
CPU FamilyID=6, Model=4D, SteppingId=8, Processor=0
Microcode Revision 12A
Platform ID: 0x10041831
PMG_CST_CFG_CTL: 0x40006
BBL_CR_CTL3: 0x7E2801FF
Misc EN: 0x4000840081
Gen PM Con1: 0x3808
Therm Status: 0x8852000F
POST Control=0xEA000301, Status=0xE6000000
Last boot POST Status=0xDF00

BIOS initializations...
15, 00068001, 19, 00068000,
CPGC Memtest ................................ PASS

POST:
RTC Battery OK at last cold boot
RTC date 3/5/2022 8:34:27

POST SPD test ............................... PASS

POST Lower DRAM Memory test
.... Perf cnt (curr,fixed): 0x42357E2C1,0x42990A4D9

POST Lower DRAM Memory test ................. PASS
POST Lower DRAM ECC check ................... PASS

37, 00068003, 3B, 00068002, 4F,
PEIM: DxE Load Core (03021001)
60, DXE_CORE_STARTED (03041000)
61, 9A, 02020000, 78, 68, 69, 00068005, 6A, 70, 71, 79, 03058001, 90,
DXE_BDS_STARTED (03041001), 91, 92,
PciBusStart(02010000): 94, 02011000, 94, 02011000, 94, 02011000, 94, 02011000, 94, 02011000, 95, 96, 97,
98, 9D, 02020004, 9C, 02020003, B4, 92,
PciBusStart(02010000): A0,
AhciBusStart (02080000), A2, A2, A2, A2, A0,
AhciBusStart (02080000), A2, SATA ConfigureDevice Port 0: Device InnoDisk Corp. - mSATA 3IE3 Pass
A2,
Booting S4128T-ON
28 port x 10GBT + 2 port x 100G QSFP28

Primary BIOS
System CPLD Version 1.3, Master CPLD Version 1.2

Last Reset Reason 0xC0

DxE POST
HDD Access .................................. PASS
Storage device is GPT formatted.

POST Upper DRAM Memory test
Short memory cell test
....
POST Upper DRAM Memory test ................. PASS
POST PCI test ............................... PASS
POST NVRAM check ............................ PASS
POST overall test results ................... PASS

NVRAM: 00 DF 00 E6 01 03 00 EA

Version 2.17.1245. Copyright (C) 2020 American Megatrends, Inc.
BIOS Date: 11/24/2020 09:35:24 Ver: 0ACBZ038
Press or to enter setup. AD,

Welcome to GRUB!

error: syntax error.
error: Incorrect command.
error: syntax error.

GNU GRUB version 2.02~beta2+e4a1fe391

/----------------------------------------------------------------------------\
|*OS10-A |
| OS10-B |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
\----------------------------------------------------------------------------/

Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, `e' to edit the commands
before booting or `c' for a command-line.
The highlighted entry will be executed automatically in 0s.
Booting `OS10-A'

Loading OS10 ...
AF,

DXE_EXIT_BOOT_SERVICES(03101019)
B0, B1, [ 0.929124] esas2r: driver will not be loaded because no ATTO esas2r devices were found
[ 2.033118] intel_rapl: driver does not support CPU family 6 model 77
WARNING: Failed to connect to lvmetad. Falling back to device scanning.
<165>1 2022-03-05T11:34:11.714639+03:00 switch_name dn_alm 805 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %NDM_SYSTEM_RELOAD: User request to reload system Cold reload system
<165>1 2022-03-05T11:34:11.940584+03:00 switch_name dn_alm 805 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %ALM_AUTH_EVENT: Authentication event was raised MESSAGE=pam_unix(sshd:session): session closed for user admin

Debian GNU/Linux 9 switch_name ttyS0

Dell EMC Networking Operating System (OS10)

switch_name login: [ 17.001778] linux-kernel-bde (1002): MSI not used
<165>1 2022-03-05T11:35:08.863153+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], %ALM_CLOCK_UPDATE: Clock changed MESSAGE=apt-daily.timer: Adding 1h 27min 37.666656s random time.
<165>1 2022-03-05T11:35:08.863715+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], %ALM_CLOCK_UPDATE: Clock changed MESSAGE=Started Daily apt download activities.
<165>1 2022-03-05T11:35:09.365482+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %ALM_SYSTEM_RESTART: OS10 Event and Alarm management system restarted
<161>1 2022-03-05T11:35:29.584712+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [alarm], Dell EMC (OS10) %PM_SYS_UTIL_HI: CPU Utilization 1-minute High Threshold alarm Raised: 100.00 (85-75) %%ACTION=RAISED %%SEQUENCE=4856
<164>1 2022-03-05T11:35:29.596946+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [alarm], Dell EMC (OS10) %PM_SYS_UTIL_LO: CPU Utilization 1-minute Low Threshold alarm Raised: 100.00 (85-75) %%ACTION=RAISED %%SEQUENCE=4857
<165>1 2022-03-05T11:35:58.352097+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [alarm], Dell EMC (OS10) %PM_SYS_UTIL_HI: CPU Utilization 1-minute High Threshold alarm Cleared: 79.48 (85-75) %%ACTION=CLEARED %%SEQUENCE=4856
<165>1 2022-03-05T11:36:02.754309+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_UNIT_DETECTED: Unit present unit 1
<165>1 2022-03-05T11:36:02.755527+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_PSU_DETECTED: Power supply unit present PSU 1
<165>1 2022-03-05T11:36:02.756132+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_PSU_DETECTED: Power supply unit present PSU 2
<165>1 2022-03-05T11:36:02.761374+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_FAN_TRAY_DETECTED: Fan tray present fan tray 1
<165>1 2022-03-05T11:36:02.768752+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_FAN_TRAY_DETECTED: Fan tray present fan tray 2
<165>1 2022-03-05T11:36:02.770166+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_FAN_TRAY_DETECTED: Fan tray present fan tray 3
<165>1 2022-03-05T11:36:02.770794+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_FAN_TRAY_DETECTED: Fan tray present fan tray 4
<165>1 2022-03-05T11:36:04.458495+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_UNIT_CHECKIN: Unit check-in detected unit 1 (type S4128T-ON 28x10GbE copper, 2x100GbE QSFP28 Interface Module)
<165>1 2022-03-05T11:36:04.466221+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %EQM_UNIT_UP: Unit is up unit 1
<165>1 2022-03-05T11:36:05.573447+03:00 switch_name dn_alm 779 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %CMS_INIT_STATE: init state enum state 5

Can you tell me how to see what caused the error?
how to update ssd?