S4048-on LACP issues

Hi there,

I'm new to Force10 world - more a Juniper/Cisco guy :)

Anyway, trying to configure basic port-chann between s4048on and a router.

I've followed config guide that I found but still, port-chann doesn't show interface members.

On the other end is a Cisco switch with standard configuration.

Dell#sh ver
Dell Real Time Operating System Software
Dell Operating System Version:  2.0
Dell Application Software Version:  9.10(0.1)
Copyright (c) 1999-2016 by Dell Inc. All Rights Reserved.
Build Time: Wed May 11 23:07:56 2016
Build Path: /sites/eqx/work/swbuild01_1/build08/E9-10-0/SW/SRC
Dell Networking OS uptime is 5 day(s), 12 hour(s), 21 minute(s)

System image file is "system://A"

System Type: S4048-ON
Control Processor: Intel Rangeley with 3 Gbytes (3201302528 bytes) of memory, core(s) 2.

8G bytes of boot flash memory.

  1 54-port TE/FG (SK-ON)
 48 Ten GigabitEthernet/IEEE 802.3 interface(s)
  6 Forty GigabitEthernet/IEEE 802.3 interface(s)
Dell#

Here's what i have and what i've done:

Dell#sh inter po br
Codes: L - LACP Port-channel
       O - OpenFlow Controller Port-channel
       A - Auto Port-channel
       I - Internally Lagged

    LAG  Mode  Status       Uptime      Ports
L   10   L2    down         00:00:00
Dell#sh inter po10 | g Mem
Members in this channel:
Dell#sh run inter po10
!
interface Port-channel 10
 no ip address
 switchport
 lacp long-timeout
 no shutdown
Dell#sh run inter po10
!
interface Port-channel 10
 no ip address
 switchport
 lacp long-timeout
 no shutdown
Dell#sh run inte te1/47
!
interface TenGigabitEthernet 1/47
 no ip address
!
 port-channel-protocol LACP
  port-channel 10 mode active
  lacp port-priority 1
 no shutdown
Dell#sh run inte te1/48
!
interface TenGigabitEthernet 1/48
 no ip address
!
 port-channel-protocol LACP
  port-channel 10 mode active
 no shutdown
Dell#sh lacp 10
Port-channel 10 admin up, oper down, mode lacp
LACP Fast Switch-Over Disabled
Actor   System ID:  Priority 1, Address e4f0.041a.3705
Partner System ID:  Priority 0, Address 0000.0000.0000
Actor Admin Key 10, Oper Key 10, Partner Oper Key 0, VLT Peer Oper Key 10
LACP LAG 10 is an individual link

LACP LAG 10 is a normal LAG

A - Active LACP, B - Passive LACP, C - Short Timeout, D - Long Timeout
E - Aggregatable Link, F - Individual Link, G - IN_SYNC, H - OUT_OF_SYNC
I - Collection enabled, J - Collection disabled, K - Distribution enabled
L - Distribution disabled, M - Partner Defaulted, N - Partner Non-defaulted,
O - Receiver is in expired state, P - Receiver is not in expired state

Port Te 1/47 is enabled, LACP is enabled and mode is lacp
Port State: Not in Bundle
  Actor   Admin: State ADEHJLMP Key 10 Priority 1
           Oper: State ADEHJLMP Key 10 Priority 1
  Partner is not present

Port Te 1/48 is enabled, LACP is enabled and mode is lacp
Port State: Not in Bundle
  Actor   Admin: State ADEHJLMP Key 10 Priority 32768
           Oper: State ADEHJLMP Key 10 Priority 32768
  Partner is not present
Dell# sh vlan id 101

Codes: * - Default VLAN, G - GVRP VLANs, R - Remote Port Mirroring VLANs, P - Primary, C - Community, I - Isolated
       O - Openflow
Q: U - Untagged, T - Tagged
   x - Dot1x untagged, X - Dot1x tagged
   o - OpenFlow untagged, O - OpenFlow tagged
   G - GVRP tagged, M - Vlan-stack
   i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged

    NUM    Status    Description                     Q Ports
    101    Active                                    T Po10()
                                                     U Te 1/3
Dell#

Any help is greatly appreciated

Cheers