urgent s4048

Question

Hi, I have now 2 switch s4048.One(switch 1) is running and the other one is brand new (switch 2) that replaced an broken switch s4048. The 2 switches are connected by lag5 (port 49 with port 49 and port 50 with port 50) Switch 1 :port 1/25 connected to router 1. Switch 2.port 1/25 will be connected to router 2. On the new switch -brand new: Dell>#configure Dell(conf)#interface ManagementEthernet 1/1 Dell(conf-if-ma-1/1)#no shutdown Dell(conf-if-ma-1/1)#ip address 10.68.229.90/24 Dell(conf-if-ma-1/1)#exit Dell(conf)#username admin password admin Dell(conf)#enable password admin Configure port channel for LAG These commands configure the switch interconnect as a LAG. Dell(conf)#interface Port-channel 5 Dell(conf-if-po-1)#mtu 12000 Dell(conf-if-po-1)#switchport Dell(conf-if-po-1)#no shutdown Dell(conf-if-po-1)#exit Configure QSFP ports for LAG These commands assign 40Gb QSFP ports to the Port Channel. Dell(conf)#interface range fortyGigE 1/49 , fortyGigE 1/50 Dell(conf-if-range-fo-1/49,fo-1/50)#no ip address Dell(conf-if-range-fo-1/49,fo-1/50)#mtu 12000 Dell(conf-if-range-te-1/49,fo-1/50)#no shutdown Dell(conf-if-range-fo-1/49,fo-1/50)#flowcontrol rx on tx off Dell(conf-if-range-fo-1/49,fo-1/50)#port-channel-protocol lacp Dell(conf-if-range-fo-1/49,fo-1/50-lacp)#port-channel 5 mode active Dell(conf-if-range-fo-1/49,fo-1/50-lacp)#exit Dell(conf-if-range-fo-1/49,fo-1/50)#exit Dell(conf)#exit conf interface vlan 229 description RTA staging OAM interface te 1/25 switchport interface vlan 229 tag te 1/25 ip addr 10.68.229.45/26 no shutdown exit   I connected next the router to 1/25.   show interfaces te 1/25 link is up protocol is down. where is the issue? the cable between router and switch is good.   should i connect the router to port 1/1 to copy the below file? should i connect all the cables 1/1-1/8 to this switch?   From switch i am not able to ping anything. I like to copy by ftp startup-config from the switch 1 to switch 2. config ftp server on switch 2. conf ftp-server enable exit show run ftp config ftp-server topdir flash: ftp-server username admin password admin   config ftp client on switch 1 conf ip ftp source-interface vlan 229 ip ftp password admin ip ftp username admin   i am not able to copy . I need a solution because this is i production. tnx      I did not started with the below.Can be this the issue? Dell>enable Dell#delete startup-config Proceed to delete startup-config [confirm yes/no]yes Dell#reload System configuration has been modified. Save? [yes/no]no Proceed with reload [confirm yes/no]yes

DELL-Josh Cr · Answer

Hi, Are the firmware versions the same? Are the speeds set to auto negotiate?

linuly · Answer

hi,

i have configured vlan 229 in every switch.

but port-channel 5 is not included in vlan 229 in both switches.

can be this the issue?

if i include port-channel 5 then can i copy startup-config from a switch to other switch?

conf
interface vlan 229

interface port-channel 5

exit

DELL-Josh Cr · Answer

I would try adding it and seeing if that works.

linuly · Answer

tomorrow i will test them.if i will have an answer will be great.

linuly · Answer

hi, i setup as i wrote.when i connected the router to switch the traffic go down to 5%. we like to find out why.

DELL-Josh Cr · Answer

Can you private message me the service tag?

Networking General

Was this post helpful?