Unsolved
This post is more than 5 years old
2 Posts
0
1042
August 26th, 2018 08:00
MD3000 in reboot loop, dbm::versionConvert fail to commit
I was re-configuring an MD3000, and foolishly changed a couple of drives that were in the process of initializing. MDSM showed several errors, I turned the array off, swapped a couple more drives, and now when I power it up it's stuck in an endless reboot loop, and can't connect to the array with MDSM. There are 2 controllers - behavior is unchanged if I try running with just either one of them.
Can anyone help?
I've attached a serial cable, and am getting the following output from power on until the first reboot:
-=<###>=-
Attaching interface lo0... done
Adding 9766 symbols for standalone.
Error
08/26/18-15:19:44 (GMT) (tRootTask): NOTE: I2C transaction returned 0x0423fe00
Reset, Power-Up Diagnostics - Loop 1 of 1
3600 Processor DRAM
01 Data lines Passed
02 Address lines Passed
3300 NVSRAM
01 Data lines Passed
5900 Ethernet 91c111 #1
01 Register read Passed
02 Register test Passed
3A00 NAND Flash
06 Bad Blocks Test Passed
2310 Application Accelerator Unit
01 AAU Register Test Passed
6D00 LSI SAS 1068 IOC--Base Board
01 IOC Register Read Test Passed
02 IOC Register Address Lines Test Passed
03 IOC Register Data Lines Test Passed
6D01 LSI SAS 1068 IOC--Host Card
01 IOC Register Read Test Passed
02 IOC Register Address Lines Test Passed
03 IOC Register Data Lines Test Passed
3900 Real-Time Clock
01 RT Clock Tick Passed
Diagnostic Manager exited normally.
Current date: 08/26/18 time: 05:19:03
Send for Service Interface or baud rate change
08/26/18-15:20:02 (GMT) (tRAID): NOTE: Set Powerup State
08/26/18-15:20:02 (GMT) (tRAID): NOTE: SOD Sequence is Normal, 0
08/26/18-15:20:02 (GMT) (tRAID): NOTE: Turning on tray summary fault LED
08/26/18-15:20:04 (GMT) (tRAID): NOTE: SYMBOL: SYMbolAPI registered.
08/26/18-15:20:04 (GMT) (tRAID): NOTE: lost persistent dq data because buffer was modified or size changed.
esmc0: LinkUp event
08/26/18-15:20:06 (GMT) (tNetCfgInit): NOTE: Network Ready
08/26/18-15:20:08 (GMT) (tRAID): NOTE: Initiating Drive channel: ioc:0 bringup
08/26/18-15:20:10 (GMT) (tRAID): NOTE: IOC Firmware Version: 00-24-63-00
08/26/18-15:20:20 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:1 phy:0 prevNumActivePhys:2 numActivePhys:2
08/26/18-15:20:20 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:1 phy:1 prevNumActivePhys:2 numActivePhys:2
08/26/18-15:20:20 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:0 phy:2 prevNumActivePhys:2 numActivePhys:2
08/26/18-15:20:20 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:0 phy:3 prevNumActivePhys:2 numActivePhys:2
08/26/18-15:20:20 (GMT) (tSasCfg017): NOTE: Alt Controller path up - chan:1 phy:18 itn:1
08/26/18-15:20:20 (GMT) (tSasCfg021): NOTE: Alt Controller path up - chan:0 phy:16 itn:2
08/26/18-15:20:21 (GMT) (IOSched): NOTE: New Initiator: 1 - channel: 1,devHandle: x15, SAS Address: 500221948c113601
08/26/18-15:20:21 (GMT) (IOSched): NOTE: New Initiator: 2 - channel: 0,devHandle: x21, SAS Address: 500221948c113600
08/26/18-15:20:21 (GMT) (tRAID): NOTE: IonMgr: Drive Interface Enabled
08/26/18-15:20:22 (GMT) (tRAID): NOTE: SOD: Instantiation Phase Complete
08/26/18-15:20:22 (GMT) (tRAID): NOTE: Inter-Controller Communication Channels Opened
08/26/18-15:20:22 (GMT) (tSasDiscCom): NOTE: SAS Discovery complete task spawned
08/26/18-15:20:22 (GMT) (iacTask1): NOTE: fbm:altValidateSubModelID: Sub-Model IDs Validated
08/26/18-15:20:22 (GMT) (tRAID): NOTE: LockMgr Role is Slave
08/26/18-15:20:22 (GMT) (sasCheckExpanderSet): NOTE: Expander Firmware Version: 0116-e05c
08/26/18-15:20:22 (GMT) (sasCheckExpanderSet): NOTE: Expander SAS address: Hi = x50022194 Low = x8dfda410
08/26/18-15:20:22 (GMT) (tRAID): NOTE: spmEarlyData: No data available
08/26/18-15:20:35 (GMT) (tSasDiscCom): WARN: SAS: Initial Discovery Complete Time: 30 seconds
08/26/18-15:20:35 (GMT) (tRAID): NOTE: WWN baseName 00040022-198c1136 (valid==>AltMacMatch)
08/26/18-15:20:38 (GMT) (tRAID): NOTE: Initiating Host channel: ioc:1 bringup
08/26/18-15:20:41 (GMT) (tRAID): NOTE: IOC Firmware Version: 00-24-63-00
08/26/18-15:20:51 (GMT) (tRAID): NOTE: sasEnableInterface: Enabling Host Interface for channel 2
08/26/18-15:20:51 (GMT) (tRAID): NOTE: sasEnableInterface: Enabling Host Interface for channel 3
08/26/18-15:20:51 (GMT) (tRAID): NOTE: IonMgr: Host Interface Enabled
08/26/18-15:20:51 (GMT) (tRAID): NOTE: SOD: Pre-Initialization Phase Complete
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab06
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab08
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab14
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab0c
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab12
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab76
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab0a
08/26/18-15:20:52 (GMT) (tRAID): NOTE: I2C transaction returned 0x0421ab77
08/26/18-15:20:52 (GMT) (tRAID): WARN: BID: initialize(): Power latched!
08/26/18-15:20:52 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:3 phy:6 prevNumActivePhys:0 numActivePhys:1
08/26/18-15:20:52 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: IOCPort: chan:3, FAILED to DEGRADED
08/26/18-15:20:52 (GMT) (tSasEvtWkr): WARN: sasIocPhyUp: Initializing Channel 3: Attached SAS Address: 5001c231cc77d504
08/26/18-15:20:53 (GMT) (tSasEvtWkr): NOTE: sasIocPhyUp: chan:3 phy:7 prevNumActivePhys:1 numActivePhys:2
08/26/18-15:20:55 (GMT) (ssmTimer): NOTE: I2C transaction returned 0x0421ab06
08/26/18-15:20:55 (GMT) (ssmTimer): NOTE: I2C transaction reporting disabled.
08/26/18-15:21:02 (GMT) (tRAID): PANIC: dbm::versionConvert fail to commit
0 events found