Search

Has anyone ever connected a S4148T (OS10) and S4048T (OS9) together via QSFP+ 40Gb? We can connect S4048Ts together all day long. We try connecting to S4148T and the port lights up for a few seconds and then the port shutdowns on the S4148T. Some background and Information: Using a Dell branded Q

HelloThe OS10 Dell Switch Security Check wants to verify the following features:However, if you look at the manual, it does not say whether the service is supported as shown below. Are the functions in the table not supported by OS10 switches? If supported, what command can I use to check it?

Hi, I have a scenario with everything duplicated. When I undo my stacked one, that is, I separate my switches and keep it with the same settings, what happens to my network? Should it keep working? Switch 1 Configuration configurevlan databasevlan 12,1000,1447vlan routing 1000 2vlan routing 1

Hi, I have dedicated ports to do the stacked. Do I need to define the ports (1/XG1 and 1/XG2) before adding my slave switch? console>enableconsole#configconsole(config)#stackconsole(config-stack)#stack-port 1/xg1 stackconsole(config-stack)#stack-port 1/xg2 stackconsole(config-stack)#endconsole

Hi, Just to give some background, I am new to this environment and need some help with a new M8024 that was ordered for PowerEdge M1000e and I was asked to try configure it. I am able to see the PowerConnect on the CMC. No Ip address has been assigned to it. I should be able to access it thro

Hi, to remove member 2 from stacked the interfaces need to be disconnected, but can it stay on? Can I disable the interface instead of physically disconnecting? I'm not physically on site and would like to remove member 2 and reconnect again to learn how it works, so I want to do it with no physi

Hi, Sorry, but its been 12 years since I've built a totally new network, so perhaps I'm just being stupid. FIrst: here is my setup: I'm replacing a largely obsolete network which has been hacked together for the last 20 years with a new paralell network based on S- series switches with core and i

Hi, Have a strange issue where I cant ping inside the 8024F from another subnet. I have two Dell R820 connected to a PC-8024F and the 8024f is connected to a CISCO 3945-e router. The problem I'm having is (once I start the esxi host or run a SoftPerfect NetworK scan on the ip range 192.168.2.0/24)

LOL I've got an N1548, with a couple VLANs. VLAN 1 (10.10.10.0) and VLAN 9 (192.168.9.0).  Computer connected to VLAN 1 with an IP of 10.10.10.50. Another connected to VLAN 9, 192.168.9.50. And I can't ping between them. I did go into Switching, VLAN and bind subnet to VLAN for both. Under R

Hi, I recently went through the troble of doing a recover password and found various threads about this, one of these was to uninstall the OS and reinstall, all this went fine but the startup.xml persisted and no changes to the admin password. After this i found out i could login with linuxadmin a

Just to call out i have already posted my issue in the Powerstore Community -- as  https://www.dell.com/community/PowerStore/PS-with-S5048F-ON-OS9-IPv6-Q/m-p/8149772#M105 OS9.. IPv6 configuration..i'm looking to enable ipv6 on an svi , using a link local address (is that an option) i see the

Hi, I'm newbie to the Dell networking. For the implementation of CCTV system Network, i have designed one topology by using MLAG and VRRP, (Please check the attached diagram). I have some queries related to this. I need active-active Network to achieve redundancy as well as throughput balancing. 1

Hi, How do I reset my switch to factory default? Thanks.

We got two new S5248F-ON which I configured with VLT. I connected lots of compute nodes with LACP to the new switches, all working fine. But I've been trying all day to connect our S4048-ON using 2x 40GBit cables and cannot get this to work. At first I thought it was STP interfering, but even w

Good day, to all. I have a question regarding a BGP configuration between AWS Direct Connect and on the premises site using a N3048 stack. I have the BGP session up and running but no routes are being publish. The question is what am i missing in the  Dell config. AWS has a default config fo

Hi, I can only access the switch by WebGui. When I make SSH connection it doesn't connect. Thanks.

Hi, How do I check the status of the (Dell EMC Networking N1148T-ON) FANs? I don't see the information in the WebGui. Is it possible to see the service tag in WebGui or SSH?   Thanks.

Good Morning All I have a stack Dell N2024 thats about 7 years old , im looking to replace them just wanted find out from the community what's the ideal replacement model.   Your feedback would much appreciated.   Regards Jesse

Hi, I don't know about networking and I'm learning now. I will receive a new one (PowerConnect 6224) for replacement and I need to install the same firmware as my current one. Where do I download the same version I'm using and how do I update? How should I connect to my computer to access it the

Hello all! We have two S5248F-ON connecting to two BES-53248 (details below). We are using 25G speed. Dell Switch: S5248F-ON OS Version: 10.5.2.7 Dell Switch side transceiver: W4GPP (AFBR-725TMZ-FT1): https://docs.broadcom.com/doc/pub_005171_DS_AFBR-725TMZ_2018_01_19 Broadcom Switch: BES-53248