Start a Conversation

Unsolved

P

1 Rookie

 • 

24 Posts

40

January 24th, 2024 18:53

SRDF Set up on VMAX system

Hello All,

We have a new Powermax system, we want to set up replication between the VMAX system to PMAX. When i try to create a dynamic SRDF group, i am getting the below error.

"A local GIGE IP table mismatch has been encountered"

I believe we need to set up RMT table, but i do not see any option to set RMT table on unisphere for this VMAX system. Is there a way we can set this up via CLI ?

Moderator

 • 

6.9K Posts

January 25th, 2024 14:22

Hello Prasad0065,

RMT is not supported on a VMAX system.

1 Rookie

 • 

24 Posts

January 25th, 2024 15:23

Our system is VMAX 450F. So now how do i setup replication to a new PMAX system ? I know the IP the interfaces on both the systems are able to communicate to each other. What else do i need to do to start creating SRDF groups.

When i try to create SRDF group, i am getting this error :

"A local GIGE IP table mismatch has been encountered"

Moderator

 • 

6.9K Posts

January 25th, 2024 16:59

Hello Prasad0065,

Here is a link to the powermax info hub and if you look under Use Local and Remote Replication Services there are some guides that will be of assistance.

https://www.dell.com/support/kbdoc/en-us/000189115/powermax-info-hub-product-documentation-videos?lang=en

1 Rookie

 • 

24 Posts

January 25th, 2024 18:59

@DELL-Sam L​ I dont have any issues setting up SRDF between powermax systems. But only when i try to create SRDF group from VMAX 450F i am seeing issues.

Specifically, I would like to understand how do i resolve the below issue. When creating SRDF group, i am getting this error.

"A local GIGE IP table mismatch has been encountered"

Moderator

 • 

8.5K Posts

January 25th, 2024 19:15

Are you getting the error on the VAX or Powermax side? This might help. https://dell.to/3vTeNFy

1 Rookie

 • 

24 Posts

January 25th, 2024 20:13

@DELL-Josh Cr​ I am getting this error on VMAX.

I did try creating RMT table on the VMAX system using the commands that are present in the article. But when i do that i am getting the below error.

"The requested feature is not supported for this microcode or SYMAPI version"

Moderator

 • 

8.5K Posts

January 25th, 2024 20:16

What version are you using?

1 Rookie

 • 

24 Posts

January 25th, 2024 20:26

@DELL-Josh Cr​ 

Symmetrix Command Line Interface (SYMCLI) Version V10.1.0.0 (Edit Level: 2752)
built with SYMAPI Version V10.1.0.0 (Edit Level: 2752)

I have tried looking into V10 SE guide. I could not find any related commands.

(edited)

Moderator

 • 

8.5K Posts

January 25th, 2024 20:34

Try what is on page 247 https://dell.to/492CxVG

1 Rookie

 • 

24 Posts

January 25th, 2024 21:37

@DELL-Josh Cr​ Tried it already. Same error message.

""The requested feature is not supported for this microcode or SYMAPI version""

Moderator

 • 

8.5K Posts

January 26th, 2024 17:48

You may need to call phone support. 

No Events found!

Top