thanks for the reply.

The problem started when i had only one software - roxio. the other softwares came later.

is there any way I can tell for sure that the problem was caused by a conflict

 Sometimes there's a conflict and you'll get burns that usually stop at about 89%. If thats the case then uninstall one of the burning programs them and just use the other one.

Message Edited by JOKERSWILD on 03-04-2004 09:29 PM

I did some research and you may have a bad batch of media or  incompatable media according to the search. Try burning a disc from a different batch and see if that works.

Hi,

          You haven't mention anything about your profile of your 2400 , how much memory do you have ? What i would do first is uninstall Roxio and nero ,check and make your there are gone completely, do a disk clean up , delete all your cookies, defrag, and then go into device manager and uninstall your rewriter,reboot, windows xp will reinstall the rewriter. Then I would install Roxio.( I don't know what version you have of Roxio but I have version 6 and have had no problems with it) (version 7 is out by the way) I have found usiing fuji media to be very dependable. Now if you like Nero better than Roxio,install that instead, but not two of them on the same computer.Make sure all your windows are closed before starting your burn.Disable your antivirus software

Message Edited by Robert Moyer on 03-05-2004 04:37 AM

will do it over the weekend and let u know what happens!!

BTW, i have 640MB ram.

 

tried at least 3 batches so far. i don't htnk media is the problem. must be something to do with hardware i thnk

removed all burning software - pinnacle,roxio, nero,sonic - didn't realise had so many.

installed easy cd creater 5. got a coaster again. :(

1. when i restarted and logged back on got a "Pinnacle Driver check  - Pinnace Driver Check detected problems with your driver settings. Would you like to fix these now? " message box.

So did a search. downloaded regdelete s/w from pinnacle site and cleaned the registry. then restarted and got the message again.

Any help to remove this would be appreciated!!

2.  had easy cd creator 6 trial version. i used the removal tool downloaded form predator's webpage. It asked whether to remove ver 4 or 5. pressed ok. it left behind the entries in the program list. so guess was not a proper uninstall. now i can't do an unistall using control panel either. how do i remove this?

Also, is there a way ot check and make sure the s/w's have been properly removed?

 

 

Message Edited by adiyar on 03-09-2004 10:00 AM

---

@adiyar wrote:

removed all burning software - pinnacle,roxio, nero,sonic - didn't realise had so many.

installed easy cd creater 5. got a coaster again. :(

1. when i restarted and logged back on got a "Pinnacle Driver check  - Pinnace Driver Check detected problems with your driver settings. Would you like to fix these now? " message box.

So did a search. downloaded regdelete s/w from pinnacle site and cleaned the registry. then restarted and got the message again.

Any help to remove this would be appreciated!!

2.  had easy cd creator 6 trial version. i used the removal tool downloaded form predator's webpage. It asked whether to remove ver 4 or 5. pressed ok. it left behind the entries in the program list. so guess was not a proper uninstall. now i can't do an unistall using control panel either. how do i remove this?

Also, is there a way ot check and make sure the s/w's have been properly removed?

 

 

Message Edited by adiyar on 03-09-2004 10:00 AM

---

There is no such thing as a "Trial Version" of ECD 6! If it is something you downloaded, you got pirated junk!

Roxizap will remove anything with Adaptec or Roxio from your PC except V7.

 Thanks for ur reply. my bad about the "trial version". me lot confused abt when/how i installed so many software on my machine

i deleted all registry entries. Installed nero. performed simulation. gave me a buffer underrun error. but told me to carry on as justlink should take care of that. however the simulation log file gave me the following

 SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x022E0000
 Status:     0x04 (0x01, SCSI_ERR)
 HA-Status   0x00 (0x00, OK)
 TA-Status   0x02 (0x01, SCSI_TASTATUS_CHKCOND)
 Sense Key:  0x03 (KEY_MEDIUM_ERROR)
 Sense Code: 0x0C
 Sense Qual: 0x00

the same 03/0C/00 error.

the end of the log file with the driver info -

Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.60 (1021), size=25244 bytes, created 9/10/1999 7:06:00 AM
File 'Drivers\atapi.sys': Ver=5.1.2600.1106 (xpsp1.020828-1920), size=86912 bytes, created 8/29/2002 1:27:50 AM (Adapter driver for rec)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

Are these the proper drivers?

While doing the Current System configuration on the Dell support page, it showed the Easy CD creator 6 s/w still there. I used the roxizap and then deleted the registry entries too. Why is it still showing up?

tearing my hair out now!! :)

Any inputs appreciated.

 

chatted with Dell support abt this. told me to update my firmware. did it. R603 is my current version.

installed nero again. diff but similar error.  in addition to the 030C00 error got a 040902 error - Focus or tracking error. an improvement??

any input is appreciated!!

3:01:31 PM #35 SCSI -1135 File Cdrdrv.cpp, Line 1381
 SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x027C0000
 Status:     0x04 (0x01, SCSI_ERR)
 HA-Status   0x00 (0x00, OK)
 TA-Status   0x02 (0x01, SCSI_TASTATUS_CHKCOND)
 Sense Key:  0x03 (KEY_MEDIUM_ERROR)
 Sense Code: 0x0C
 Sense Qual: 0x00
 CDB Data:   0x2A 0x00 0x00 0x02 0xD4 0x1D 0x00 0x00 0x1B 0x00 0x00 0x00
 Sense Data: 0x71 0x00 0x03 0x00 0x00 0x00 0x00 0x0C
             0x00 0x00 0x00 0x00 0x0C 0x00
 
3:01:31 PM #36 MMC -1135 File Writer.cpp, Line 335
 Write error
 
3:01:31 PM #37 Text 0 File ThreadedTransfer.cpp, Line 222
 all writers idle, stopping conversion
 
3:01:31 PM #38 Text 0 File ThreadedTransfer.cpp, Line 216
 conversion idle, stopping reader
 
3:01:31 PM #39 SCSI -1039 File Cdrdrv.cpp, Line 1177
 SCSI Exec, HA 1, TA 1, LUN 0
 Status:     0x04 (0x01, SCSI_ERR)
 HA-Status   0x00 (0x00, OK)
 TA-Status   0x02 (0x01, SCSI_TASTATUS_CHKCOND)
 Sense Key:  0x04 (KEY_HARDWARE_ERROR)
 Sense Code: 0x09
 Sense Qual: 0x02
 CDB Data:   0x35 0x02 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
 Sense Data: 0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0C
             0x00 0x00 0x00 0x00 0x09 0x02
 
3:01:31 PM #40 CDR -1039 File WriterStatus.cpp, Line 157
 Focus or tracking error
 
3:01:31 PM #41 TRANSFER -24 File WriterStatus.cpp, Line 157
 Could not perform end of Disc-At-Once
 
3:01:31 PM #42 Phase 38 File dlgbrnst.cpp, Line 1571
 Burn process failed at 48x (7,200 KB/s)
 
3:01:31 PM #43 Text 0 File Scsicmd.cpp, Line 402
 SCSI not using temporary buffers
 20 out of 20 temporary buffers allocated
 
3:01:41 PM #44 SCSI -1039 File Cdrdrv.cpp, Line 1177
 SCSI Exec, HA 1, TA 1, LUN 0
 Status:     0x04 (0x01, SCSI_ERR)
 HA-Status   0x00 (0x00, OK)
 TA-Status   0x02 (0x01, SCSI_TASTATUS_CHKCOND)
 Sense Key:  0x04 (KEY_HARDWARE_ERROR)
 Sense Code: 0x09
 Sense Qual: 0x02
 CDB Data:   0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
 Sense Data: 0x70 0x00 0x04 0x00 0x00 0x00 0x00 0x0C
             0x00 0x00 0x00 0x00 0x09 0x02
 

Existing drivers:

Message Edited by adiyar on 03-10-2004 02:32 PM