MEM not seeing more than 1 path

Question

Hello.  I am having an issue with the Dell EqualLogic Multipathing Extension Module for VMWare and hope someone can help.  After following the installation steps in the included documents, I am only seeing one path for each LUN although I have 4 iSCSI adapters setup. iSCSI networking was setup via the setup.pl script.  Installation of this script as well as the MEM module was done through the VSphere CLI.  After installation I only see one path at a time for each LUN.  According to the installation documentation, I should see multiple paths.  I have verified that failover works (pulled a cable, and another iSCSI port takes over), but I am concerned I will not get any load balancing features.  Is this expected behavior? Since the documentation has pictures that show otherwise, I want to be sure.   Here is a brief rundown of the configuration. I can provide more info if needed. Storage – EquaLogic PS4000 (firmware 5.1.2) Group IP – 10.10.10.1 Access to LUN – setup for iQN to ESX software adapter only right now Shows only one iSCSI connection to each LUN.   Switches                 Two Dell 6224 switches connected with stacking module.  iSCSI specific settings setup for iSCSI VLan (MTU 9216, flow control, STP disabled, fast port)   Server – Dell R710 with 12 Broadcom 5709 NICs (latest firmware) ESXi 5.0 managed with VCenter 5.  Latest updates with Update Manager as of about 3 weeks ago. Networking (created by the setup.pl switch)                 1 switch tied to 4 iSCSI vmkernels and 1 storage hearbeat                 iSCSI0 – 10.10.10.151 – NIC 2                 iSCSI1 – 10.10.10.153 – NIC 3                 iSCSI2 – 10.10.10.155 – NIC 4                 iSCSI3 – 10.10.10.157 – NIC 6                 Storage Heartbeat – 10.10.10.161                 MTU - 9000 Storage                 When I go to the Managed Paths option under a LUN’s properties, I only see 1 path.                 Dell_PSP_EQL_Routed is selected Storage Adapters                 Under the software iSCSI adapter, I only see 1 path per LUN.

LHDell7 · Accepted Answer

Found the problem.  Corrupt switch config on one of the 6224's.  All indicator and activity lights looked fine on the display, but going into managment, it was hosed.  Moved the iscsi ports over to the other switch and refreshed everything.  Picked up all 4 ports as active.   Thanks again!

LHDell7 · Answer

Thanks for the quick response Don.

We have Enterprise licenses. Switching to RR had no effect.

Our build is 5.0.0 - 469512. I setup Update Manager and ran all the latest Critical and Recomended updates a few weeks ago. I will need to double check to see why it is not at the 515841 level.

Also wanted to mention that in the software iSCSI adapter properites page, under Network config....all 4 iSCSI adapters are listed, but only one is listed as "Last Active". The others are "Not Used."

LHDell7 · Answer

My mistake on the version number. Looking at the wrong number. At the ESX console it states VMKernel Build 515841.

I beleive the networking is already setup the way you described.

vSwitchISCSI

Under properties, there is a listing for iSCSI0, iSCSI1, iSCSI2, and iSCSI3.

For each one, iSCSI Port Binding is enabled. Under the NIC Teaming tab, the checkbox for "Overide Failover Options" is set. There is 1 Active NIC and 3 Unused. Fore each iSCSI kernel, they use a different NIC.

LHDell7 · Answer

I will look into doing that.  Thanks for your help, much appreciated.

EqualLogic

Was this post helpful?