This post is more than 5 years old
126 Posts
0
540534
How to calculate BTU and Power Consumption for a server or array?
What is the proper way to calculate the BTUs and Power Consumption for a particular device?
This post is more than 5 years old
126 Posts
0
540534
What is the proper way to calculate the BTUs and Power Consumption for a particular device?
Top
DELL-Geoff P
990 Posts
0
April 22nd, 2014 13:00
Unfortunately, there isn't a single tool for all of Dell's devices. Here are the links to both tools:
ESSA:
Supported Products:
http://essa.us.dell.com/dellstaronline/Launch.aspx/ESSA?c=us&l=en&s=gen
and for DCCP 3.04 web version:
Regards,
DELL-Geoff P
990 Posts
0
April 25th, 2014 08:00
Wolran,
Here is what I found using the tools:
PE 1950 BTU\watts per hour: 316.9 at 1.52 amps
PE 2850 BTU\watts per hour: 524 at 2.52 amps
PE T610 BTU\watts per hour: 184.3 at .3 amps
Regards,
WolRan
2 Posts
0
April 25th, 2014 08:00
DELL-Geoff P, this information was helpful for me also. Do you also have BTU and power consumption numbers for the following: 1950, 2850, T610
WolRan
2 Posts
0
April 25th, 2014 09:00
I’m not very familiar with power consumption numbers, so I apologize if I’m asking an ignorant question. Your response on a previous thread around the PowerEdge 2950 and 1850 was:
PowerEdge 2950 306w 1044.11 btu/h
PowerEdge 1850 440w 1501.34 btu/h
How does that compare to your responses below for the 1950, 2850 and R610?
PE 1950 BTU\watts per hour: 316.9 at 1.52 amps
PE 2850 BTU\watts per hour: 524 at 2.52 amps
PE T610 BTU\watts per hour: 184.3 at .3 amps
DELL-Geoff P
990 Posts
0
April 30th, 2014 14:00
Comparing apples to oranges. The newer servers are more efficient, using less power and producing less heat, thus providing cost savings in the datacenter.
The figures used are as if they were the only server in the rack. If you place more equipment in the rack the numbers will go up.
Regards,
StlCardsFanJWR
16 Posts
0
October 6th, 2015 13:00
It would be very nice if the tool were consistent, it states the R910 is part of the "Supported Products" but is not available as a choice when trying to use the tool. It's very frustrating to waste so much time digging for energy values on Dell's website for information that should be readily available for every server Dell has manufactured.
StlCardsFanJWR
16 Posts
0
October 12th, 2015 12:00
It would be very nice if the tool were consistent, it states the R910 is part of the "Supported Products" but is not available as a choice when trying to use the tool. It's very frustrating to waste so much time digging for energy values on Dell's website for information that should be readily available for every server Dell has manufactured.
jonathanfz
1 Message
0
October 19th, 2015 13:00
Dear:
I would consult as BTU consumption calculation for two servers
Dell PowerEdge 2950
Dell PowerEdge 2970
In the Hash I have found this information.
ranadheerk
3 Posts
1
April 25th, 2017 05:00
Hello Geoff P,
i have a question. for any particular server, say for example :- PowerEdge R520, the power consumption is 159Watts. So do you mean that this 159W is at full load? if so, how much of power/BTU is dissipated/lost when it is working at full load? how to calculate it? Any kind of help in this is appreciated.
Thanks.
mvftw
25 Posts
0
January 23rd, 2019 07:00
DVSATECH
2 Posts
0
July 20th, 2020 10:00
the links dont work.
wledena
3 Posts
0
July 29th, 2021 14:00
ESSA has been replaced by EIPT AFAIK.
https://dell-ui-eipt.azurewebsites.net/#/