Announcement Banner
UNSOLVED

davidng150

updated

23 years ago

D

davidng150

31 Posts

0

14509

November 30th, 2003 15:00

Setting Up a Network

Is it possible to set up a network with two network cards connected to two computers, and a network cable connecting the two network cards? If so, how can we do that?
  • jmwills

    2 Intern

    •

    11984 Posts

    1496

    0

    Posted November 30th, 2003 15:00

    Not only posssible, but not that difficult.  You will looking to create a local Peer to peer network.  Check the resources at www.homenethelp.com for some good resources.  Post back if you have any additional questions.

    Some quick pointers:

    1. Both machines in the same workgroup with static IP addresses.
    2. Use a crossover cable.
    3. Total cost about $30.
    4. Setup this manually away from the wizards.

     

  • jmwills

    2 Intern

    •

    11984 Posts

    1496

    0

    Posted November 30th, 2003 17:00

    Start>My Network Places>Add A Network Connection.  But this will only work after the NIC's are installed.

    But again, if you follow the advice from www.homenethelp.com, you will find this much easier to get it right the first time.

     

     

    Message Edited by jmwills on 11-30-2003 02:47 PM

  • davidng150

    31 Posts

    1502

    0

    Posted November 30th, 2003 17:00

    What page should I go to on www.homenethelp.com?

    Message Edited by davidng150 on 11-30-2003 03:38 PM

  • davidng150

    31 Posts

    1496

    0

    Posted November 30th, 2003 17:00

    How do I set it up from the wizards?
  • davidng150

    31 Posts

    1502

    0

    Posted November 30th, 2003 23:00

    I looked on this page: http://www.homenethelp.com/web/howto/HomeNet-Win2kXP.asp, and followed the instructions, but couldn't find the NETWORK PROPERTIES. Do you know where I could find it? Also, in the article, it says "Right click on the network connection for your local area network." The only thing that I see in "Network Connections" is MSN Explorer.

    Message Edited by davidng150 on 11-30-2003 09:40 PM

  • jmwills

    2 Intern

    •

    11984 Posts

    1502

    0

    Posted November 30th, 2003 23:00

  • jmwills

    2 Intern

    •

    11984 Posts

    1502

    0

    Posted December 1st, 2003 09:00

    Are you NIC cards installed yet?  If not, they msu be installed first in order to do this.  If you right click My Network Places, your adapter(s) should show up there.
  • davidng150

    31 Posts

    1502

    0

    Posted December 1st, 2003 11:00

    The only problem that I have so far is that I can't find the driver for the network card (Ethernet Controller): Adapters WAN (PPP/SLIP) Interface. I looked everywhere!

  • jmwills

    2 Intern

    •

    11984 Posts

    1502

    0

    Posted December 1st, 2003 11:00

    Go to the Device Manager (Right Click My Computer>Properties>Hardware Tab>Device Manager.

    If your Adapters are installed properly, they will be listed there.  If they are installed but not working, a yellow exclamation mark will be listed next to them.

  • davidng150

    31 Posts

    399

    0

    Posted December 1st, 2003 23:00

    Well, the Ethernet Control under "Other Devices"  has a yellow exclamation mark by it.