Dell OptiPlex 3046 System BIOS

Restart required

Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.

Before updating, please read the installation instructions and important information noted below.

Driver Id : TFTDT

Importance : Critical

Version : 1.16.0, 1.16.0 Latest version Recommended version Latest and Recommended version

Release Date : 14 Apr 2022

Download Type : System BIOS

Category : BIOS

This package contains the Dell system BIOS update. BIOS is a firmware package that is embedded on a small memory chip on the system board. It controls the keyboard, monitor, disk drives, and other devices. This update addresses Common Vulnerabilities and Exposures (CVE). Common Vulnerabilities and Exposures (CVE) is a list of security vulnerabilities and exposures that are publicly disclosed.

Download Files

File Format: This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.

File Name: OptiPlex_3046_1.16.0.exe

File size: 9.15 MB

To ensure the integrity of your download, please verify the checksum value.

MD5: 9599d030b80b235a75e201e23f1d65c6

SHA1: 958e245c703dfc7b481435e8e578a075b9938d44

SHA-256: 172e6d4f6893b9c495c9e371ef1af6bf44d6d97f9af9a0bfd39982055da14c00

Download .EXE

Installation instructions

Updating the BIOS from Windows

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.

Download and Installation
1. Click Download File.
2. Click Save to save the file to your hard drive.
3. Browse to the location where you downloaded the file.
4. Double-click the new file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.

Updating the BIOS from DOS (Non-Windows users)

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.

Installation
Note: You must provide a bootable USB drive. This executable file does not create the DOS system files.
1. Copy the downloaded file to a bootable USB drive.
2. Power on the system and then Press the F12 key.
3. Select USB Storage Device and boot to the DOS prompt.
4. Run the file by typing following command. For example:
C:\ OptiPlex_3046_X.Y.Z.exe
Where C is the drive letter of the USB device where the executable file is located and OptiPlex_3046_X.Y.Z.exe is the name of the downloaded file.
The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, system restarts again.

Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com
Note 2: Do not turn off the power or interrupt the BIOS update process during the update.
Note 3: Your system requires a restart after installing the BIOS. The restart can be deferred but must be completed to ensure that the update is installed.

Installation
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system and then go to BIOS Setup by pressing the F2 key.
3. Go to General > Boot Sequence > Boot > Boot List Option.
4. Change UEFI to Legacy of Boot List Option.
5. Go to Exit > Save Changes and reboot system.
6. Press F12 and then select USB Storage Device and boot to the DOS prompt.
7. Run the file by typing the file name.
8. The system restarts automatically and updates the BIOS at the system startup screen. After the BIOS update is complete, the system restarts again.
9. Go to BIOS Setup by pressing the F2 key and go to General > Boot Sequence > Boot > Boot List Option.
10. Change Legacy to UEFI Boot Option.
11. Go to Exit > Save Changes and reboot the system.

Updating the BIOS from BIOS Boot Menu (independent of operating system)

Note 1: Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If BitLocker is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM

Dell OptiPlex 3046 System BIOS

Download Files

Fixes & Enhancements

Important Information

Compatible Systems

Supported Operating Systems

Installation instructions

Applies to