Connectrix:故障診斷 xbar 問題
Summary: 本文說明如何針對 xbar 問題進行故障診斷。最近,該領域的任務是更換幾台機甲,最終不需要。
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Instructions
當 xbar 出現錯誤,且模組故障,通常會執行機械更換。
若要故障診斷 xbar 問題,隔離問題 (前提是客戶允許) xbar、監管程式、任何線路卡和機箱。
執行隔離工作以處理 xbar 失敗。此程序需要執行下列步驟以進行隔離:
- 取代
xbar。
如果更換失敗,則問題不在xbar。 - 隨著更換
xbar仍插入狀態,執行 系統切換 (等待維護時段) 以交換使用中和待機監管程式,並檢查 XBAR 狀態。由於這些模組可熱交換,因此您可以嘗試重新插入舊的xbar如果更換仍然失敗。
注意:請務必保留至少一個
xbar 在 MDS 9500 中至少有兩個,在 MDS 9700 交換器中至少有兩個,否則系統會故障。請勿全部移除 xbars。
2016 Jul 17 14:42:39 MDSswitch Jul 27 14:42:38 %KERN-2-SYSTEM_MSG: [25315862.942013] Switchover started by redundancy driver - kernel 2016 Jul 17 14:42:39 MDSswitch %SYSMGR-2-HASWITCHOVER_PRE_START: This supervisor is becoming active (pre-start phase)
- 如果
xbar仍處於關閉狀態,且已發生切換, 請收集show tech-support details輸出並查看異常日誌。在許多情況下,異常記錄會顯示來自CHICO ASIC。
exception information --- exception instance 7 ----
Module Slot Number: 7
Device Id : 145
Device Name : Sacramento Xbar ASIC
Device Errorcode : 0xc9100200
Device ID : 145 (0x91)
Device Instance : 00 (0x00)
Dev Type (HW/SW) : 02 (0x02)
ErrNum (devInfo) : 00 (0x00)
System Errorcode : 0x41ec006d SAC sync lost
Error Type : Warning
PhyPortLayer : Fibre Channel
Port(s) Affected :
Error Description : Lost sync on slot:7 asic:0 chico:19-->connected to-->Fab-1 link-01
DSAP : 0 (0x0)
UUID : 0 (0x0)
Time : Wed Jul 17 14:43:09 2016
(Ticks: 579900BD jiffies)
- 如果發生這種情況,請移除並更換該線路卡,然後嘗試重新插入
xbar卸下線路卡後。
Affected Products
Connectrix MDS-Series HardwareProducts
Connectrix MDS-9513, Connectrix MDS-9706, Connectrix MDS-9710, Connectrix MDS-9718, Connectrix MDS-Series HardwareArticle Properties
Article Number: 000006063
Article Type: How To
Last Modified: 20 Mar 2026
Version: 7
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.