PowerEdge：iDRAC 未正確顯示 ESXi 主機名稱和作業系統
Summary: 為執行 VMware ESXi 6.5 和更新版本的伺服器，提供在 iDRAC 中填入系統主機名稱和作業系統的步驟。
This article applies to
This article does not apply to
This article is not tied to any specific product.
Not all product versions are identified in this article.
Symptoms
iDRAC 使用者可能會注意到，在 iDRAC Web 和 CLI 介面中，Dell EMC PowerEdge 伺服器並未報告 VMware ESXi 6.5 或 6.7 系統主機名稱和作業系統欄位。此行為與先前在具有 VMware ESXi 6.0 及更舊版本的 Dell EMC PowerEdge 伺服器上所出現的行為不同。
Cause
iDRAC 不會輪詢作業系統的主機名稱。作業系統透過 CIM 提供者將主機名稱推送至 iDRAC 控制器。在 ESXi 6.0 中，CIM 提供者預設為啟用。此行為在 ESXi 6.5 中已變更。CIM 提供者預設為停用。
Resolution
若要修正此行為，您必須透過 ESXCLI 啟用 CIM 提供者，然後將主機重新開機。
esxcli system wbem set –e true
/etc/init.d/sfcbd-watchdog start
重新開機完成後，重新整理 iDRAC，您應該會看到載入的主機名稱已更新。
在較新的 ESXi 6.5 和 6.7 組建中，啟用 wbem 仍無法在 iDRAC 中顯示正確的 ESXi 主機名稱。這是因為已移除此功能的 VMware 刻意變更 （使用內建 CIM 提供者將主機名稱寫入 BMC）。未來的意圖是讓 hostd 服務執行此功能。
如果啟用 wbem （如上所列指示） 無法解決問題，建議在 ESXi 作業系統中安裝 ESXi 適用的 Dell EMC iSM （iDRAC Service Module） 或 OpenManage Server Administrator vSphere Installation Bundle （VIB）。
Affected Products
iDRAC7, iDRAC8, iDRAC9, VMware ESXi 6.5.X, VMware ESXi 6.7.X, VMware ESXi 6.x, VMware ESXi 7.xProducts
iDRAC Service Module, PowerEdge FC640, PowerEdge M640, PowerEdge M640 (for PE VRTX), PowerEdge MX740C, PowerEdge MX840C, PowerEdge R240, PowerEdge R250, PowerEdge R340, PowerEdge R350, PowerEdge R440, PowerEdge R450, PowerEdge R540, PowerEdge R550
, PowerEdge R640, PowerEdge R6415, PowerEdge R650, PowerEdge R650xs, PowerEdge R6515, PowerEdge R6525, PowerEdge R740, PowerEdge R740XD, PowerEdge R740XD2, PowerEdge R7415, PowerEdge R7425, PowerEdge R750, PowerEdge R750XA, PowerEdge R750xs, PowerEdge R7515, PowerEdge R7525, PowerEdge R840, PowerEdge R940, PowerEdge R940xa, PowerEdge T140, PowerEdge T150, PowerEdge T340, PowerEdge T350, PowerEdge T440, PowerEdge T550, PowerEdge T640
...
Article Properties
Article Number: 000142904
Article Type: Solution
Last Modified: 04 Dec 2024
Version: 7
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.