Connectrix：由于 Cisco 交换机中的分区模式不匹配，ISL 未传递 vSAN 流量

Zone merge failure, isolating interface fc4/1 received reason: Zoning modes does not match Received rjt from adjacent switch:[reason:0].

show zone status vsan 1-4093

输出示例：

VSAN: 10 default-zone: deny distribute: active only Interop: default  (<--VSAN 10 is the affected VSAN in this example)
    mode: enhanced merge-control: allow
    session: none
    hard-zoning: enabled broadcast: unsupported
Default zone:
    qos: none broadcast: unsupported ronly: unsupported
Full Zoning Database :
    DB size: 4 bytes
    Zonesets:0  Zones:0 Aliases: 0
Active Zoning Database :
    Database Not Available
Status:  

接口详细信息显示 VSAN 10 已隔离。您可以使用以下命令验证 VSAN 是否已隔离：

show interface fc4/1

输出示例：
（在此示例中，fc4/1 是接口。fc4/1 是中继接口（并非所有 VSAN 都在中继上正常运行。）

  Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)
    Port WWN is 20:01:00:05:73:cb:a9:80
    Peer port WWN is 20:01:00:05:73:cf:f5:f0
    Admin port mode is E, trunk mode is on
    snmp link state traps are enabled
    Port mode is TE
    Port vsan is 1
    Speed is 8 Gbps
    Rate mode is dedicated
    Transmit B2B Credit is 32
    Receive B2B Credit is 500
    B2B State Change Number is 14
    Receive data field Size is 2112
    Beacon is turned off
    Trunk vsans (admin allowed and active) (1,10)
    Trunk vsans (up)                       (1)
    Trunk vsans (isolated)                 (10)
    Trunk vsans (initializing)             ()
    5 minutes input rate 152 bits/sec, 19 bytes/sec, 0 frames/sec
    5 minutes output rate 56 bits/sec, 7 bytes/sec, 0 frames/sec
      4520 frames input, 318268 bytes
        0 discards, 0 errors
        0 CRC,  0 unknown class
        0 too long, 0 too short
      4896 frames output, 392484 bytes
        0 discards, 0 errors
      52 input OLS, 30 LRR, 12 NOS, 11 loop inits
      52 output OLS, 38 LRR, 32 NOS, 15 loop inits
      500 receive B2B credit remaining
      32 transmit B2B credit remaining
      28 low priority transmit B2B credit remaining
    Interface last changed at Mon May 10 11:51:54 2011 

使两个交换机上的分区模式一致（增强或基本），然后暂停 VSAN 10 并再次启用。
 

1. （如果二者一致，请跳过此步骤。）使两个交换机上的分区模式一致。为 enhanced 运行以下命令：

switch# config t
switch(config)# zone mode enhanced vsan 10 
switch(config)# zone commit vsan 10

使两个交换机上的分区模式一致。运行以下命令 基本：

switch# config t
switch(config)# no zone mode enhanced vsan 10

2. 使用以下命令挂起和启用 VSAN：

switch# config t
switch(config) #  vsan database
switch (config-vsan-db) #vsan 10 suspend
switch (config-vsan-db) #no vsan 10 suspend

请观看此视频：