Dell Chassis Management Controller Version 2.10 for PowerEdge FX2 and FX2s RACADM CLI Guide

Description

Deploys blade server or IOM by specifying the required properties.

To use this subcommand, you must have the Server Administrator privilege.

• racadm deploy -m < module> -u root -p < password> -s < ipaddress> < subnet> < gateway> -b < device> -o < no|yes>
• racadm deploy -m < module> -u root -p < password> -s -6 < ipv6Address> < prefixlen> < gateway> -b < device> -o < no|yes>

  where < prefixlen> is a number between 0 and 128.

• racadm deploy -m < module> -u root -p < password> -d [-6]
• racadm deploy -a -u root -p < password>

• -b < device > — Specifies the first boot device; must be used with -o.
• Use with -m < module> to specify for an individual server, or with -a for all servers

  Legal values: device=None, PXE, HDD, CD-DVD, vFDD, vCD-DVD, SD, FDD, RFS

• -o < no|yes > — Indicates if the server should boot from the device once; must be used with -o.

  Use with -m < module> to specify for an individual server, or with -a for all servers.

• -a — server/switch. Applies options to all modules present in the chassis of the given module type. Specify the value as server or switch. Default value is server. Switches must support Ethernet Management.
• -u root — Indicates that the < password > is supplied for the root user on the server. root is a constant parameter, the only value that is valid with the ‑u option. Required Username when you are setting IOA values.
• -m < module > — Specifies the server you want to configure.
  Legal value must be one of the following values:

  • server-n where n=1–4

  • switch-n where n=1–2.

• -p < password > — Specifies the password for the root user on the server or switch.

  Legal values: For switches, valid passwords are 6 - 32 ASCII characters in length, ranging in value 32–125 (decimal). For servers, valid passwords are 1 – 20 ASCII characters in length, ranging in value 32 – 126 (decimal).

• -s < ipaddress subnet gateway> — Sets the IP address, subnet mask, and gateway for the specified server, separated by single spaces.
  • ipaddress — A string representing a valid IP address. For example, 192.168.0.20.
  • subnet — A string representing a valid subnet mask. For example, 255.255.255.0.
  • gateway — A string representing a valid gateway address. For example, 192.168.0.1.
• -d — Enables DHCP for the specified server.

  The -s and -d options cannot be used together in the same command.

• -6 — Enables IPv6 auto configuration (when used with -d.) Sets static IPv6 addresses (when used with -s).
• -v —SNMPv2 community string. Valid community strings are 1–20 characters in length, with valid ASCII characters in the range [33–125] (decimal). Protocol version set to SNMPv2. Permission on community string is read-only.
  • NOTE: This input is available in IOA only.
• -q— Displays or modifies the quick deploy parameters.
• -n— Specifies the number of reserved IP addresses for quick deploy. The valid values are 2 and 4.
• -e — Uses the CMC DNS settings for quick deploy. The legal values are:
  • 1 — Enable
  • 0 — Disable
• --qd — Updates the quick deploy parameters to the servers. This option works only with the -q option.

• racadm deploy -m server-1 -s 192.168.0.20 255.255.255.0 192.168.0.1

  The server was deployed successfully.

  The deploy command generates an error when used on the extension slot of a multi-slot server.

• racadm deploy -m server-2 192.168.0.11 255.255.255.0 192.168.0.1

  ERROR: Server in slot 9 is an extension of the server in slot 1.

• racadm deploy -m server-1 -u root -p <default root user password> -s -6 ::/64 :: 10