- Notes, cautions, and warnings
- Dell Technologies Boot Optimized Storage Solution-S2
- Applications supported by BOSS-S2
- Update the BOSS-S2 firmware version
- Features of BOSS-S2
- Install and remove a BOSS-S2 card
- Driver support for BOSS-S2
- BOSS-S2 UEFI configuration utility
- Enter the BOSS-S2 UEFI configuration utility
- Exit the BOSS-S2 UEFI configuration utility
- Navigate to BOSS-S2 configuration utility
- Physical or virtual disk information
- Create a virtual disk
- Delete a virtual disk
- Recover or rebuild a degraded virtual drive
- Erase physical disk data
- View RAID controller information
- Manage BOSS-S2 using CLI commands
- Troubleshooting
- Importing the BOSS ESXi CLI offline bundle may fail in VSphere Lifecycle Manager
- BOSS ESXi CLI package fails when upgrading from Dell EMC customized versions of 6.7.x to version 7.0
- M.2 drive firmware update from iDRAC fails on unconfigured drives with an existing adapter key on the BOSS-S2 controller
- Unconfigured drives in the BOSS-S2 controller is unavailable for operating system installation with an existing adapter key
- The ROM version for BOSS is reported as firmware version in IDRAC interface
- Unable to update the M.2 drive firmware by using iDRAC or Lifecycle Controller
- BOSS-S2 CLI displays No Adapter Found error in Linux
- LC log displays fan unavailability error
- Physical disk size is not updated on iDRAC when CSIOR is disabled
- Physical disk or virtual disk is indicated as missing on iDRAC when CSIOR is disabled
- The Back Ground Activity (BGA) task process in HII does not report real-time status
- Virtual disk related events are repeatedly generated in BOSS-S2 and OMSS
- Characters are limited when entering a virtual drive name
- VMFS datastore is disabled from YX5X of PowerEdge systems that are shipped with VMware ESXi installed on BOSS-S2
- One or more physical disks are not detected by the operating system
- Virtual disk is not detected by the operating system
- An installed drive is not listed in the BOSS-S2 Configuration Utility
- The BOSS-S2 card is not presented to the PowerEdge server
- Unable to boot to M.2 drive installed in slot 1
- Unsupported commands, options, and features are displayed by BOSS-S2 CLI with VMware CLI utility
- Unable to deploy ESXi on RAID 1 of BOSS-S2
- Getting help
- Documentation resources
Willkommen
Dell Standorte
Dell Standorte
Willkommen bei Dell
Mein Konto
- Bestellungen schnell und einfach aufgeben
- Bestellungen anzeigen und den Versandstatus verfolgen
- Profitieren Sie von exklusiven Prämien und Rabatten für Mitglieder
- Erstellen Sie eine Liste Ihrer Produkte, auf die Sie jederzeit zugreifen können.
- Verwalten Sie mit der Unternehmensverwaltung Ihre Dell EMC Seiten, Produkte und produktspezifischen Kontakte.
Dell Technologies Boot Optimized Storage Solution-S2 User's Guide
Install the BOSS-S2 module
Prerequisites
CAUTION:Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the system.
- Follow the safety guidelines listed in the Safety instructions.
- Follow the procedure listed in the Before working inside your system.
NOTE:The below procedure is applicable to 1U systems. For more information on 2U systems, see the system-specific
Installation and Service Manual available at
www.dell.com/poweredgemanuals.
Steps
- Align the M.2 card at an angle with the M.2 card carrier.
- Insert the M.2 card until it is firmly seated in the M.2 card carrier.
- Using a Phillips #1 screwdriver, secure the M.2 card to the M.2 card carrier with the screw.
CAUTION:Ensure that the screws are tightened by using a torque of 1.7 in-lb (0.19 N-m).
Figure 1. Install the screw that secures the M.2 card to the M.2 card carrier 
- Slide the bracket on the BOSS-S2 module. Using a Phillips #1 screwdriver, secure the bracket on the BOSS-S2 module with the screw.
Figure 2. Install the screw of the bracket on the BOSS-S2 module 
- Slide the BOSS-S2 module into the BOSS-S2 module bay until it is firmly seated.
- Using a Phillips #1 screwdriver, secure the BOSS-S2 module with the two screws.
CAUTION:Ensure that the screws are tightened by using a torque of 4 in-lb (0.45 N-m).
Figure 3. Install the screws that secure the BOSS-S2 module 
- Connect the BOSS-S2 module power cable and signal cable to the system board.
- Slide the M.2 card carrier into the BOSS-S2 module bay.
Figure 4. Slide the M.2 carrier into the BOSS-S2 module bay 
- Slide the M.2 blank into the BOSS-S2 module bay to lock the carrier in place.
NOTE:An M.2 blank is installed only if the controller has one M.2 carrier.
Figure 5. Slide the M.2 blank into the BOSS-S2 module bay 
Next steps
- Follow the procedure listed in After working inside your system.
Bitte geben Sie eine Bewertung ab (1 bis 5 Sterne).
Bitte geben Sie eine Bewertung ab (1 bis 5 Sterne).
Bitte geben Sie eine Bewertung ab (1 bis 5 Sterne).
Bitte geben Sie an, ob der Artikel hilfreich war.
Die folgenden Sonderzeichen dürfen in Kommentaren nicht verwendet werden: <>()\