- Notes, cautions, and warnings
- Dell PowerEdge FC830 system overview
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing sled components
- Safety instructions
- Recommended tools
- Sled
- Inside the sled
- Cooling shroud
- Cooling shroud retention bar
- System memory
- Processor blank and DIMM blank
- Processors
- PCIe mezzanine card
- PCIe mezzanine card support bracket
- Internal dual SD module (optional)
- rSPI card (optional)
- SD vFlash card
- Network daughter card
- Hard drives or SSDs
- Hard-drive or SSD bay numbering
- Hard drive or SSD installation guidelines
- Removing a hard drive or SSD
- Installing a hard drive or SSD
- Removing a hard drive or SSD blank
- Installing a hard drive or SSD blank
- Shutdown procedure for servicing a hard drive or SSD
- Configuring the boot drive
- Removing a 2.5-inch hard drive or SSD from a 2.5-inch hard drive or SSD carrier
- Installing a 2.5-inch hard drive or SSD in a 2.5-inch hard-drive or SSD carrier
- Removing a 1.8-inch SSD from a 1.8-inch SSD carrier
- Installing a 1.8-inch SSD in a 1.8-inch SSD carrier
- Hard-drive or SSD cage
- Hard drive or SSD backplane
- Removing a 2.5 inch (x8) SATA hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SATA hard-drive or SSD backplane
- Removing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Installing a 2.5-inch (x8) SAS hard-drive or SSD backplane
- Removing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Installing a 2.5-inch (x6) SATA hard drive or SSD and 2.5-inch (x2) PCIe SSD backplane
- Removing a 1.8-inch (x16) SAS SSD backplane
- Installing a 1.8-inch (x16) SAS SSD backplane
- Storage controller card
- Expander card
- System battery
- System board
- Trusted Platform Module
- Using system diagnostics
- Jumpers and connectors
- Troubleshooting your system
- Getting help
Dell PowerEdge FC830 Owner's Manual
Processor Settings details
About this task
- Option
- Description
- Logical Processor
- Enables or disables the logical processors and displays the number of logical processors. If this option is set to Enabled, the BIOS displays all the logical processors. If this option is set to Disabled, the BIOS displays only one logical processor per core. This option is set to Enabled by default.
- Alternate RTID (Requestor Transaction ID) Setting
- Modifies Requestor Transaction IDs, which are QPI
resources. This option is set to Disabled by default.NOTE: Enabling this option may negatively impact the overall system performance.
- Virtualization Technology
- Enables or disables the additional hardware capabilities provided for virtualization. This option is set to Enabled by default.
- Address Translation Service (ATS)
- Defines the Address Translation Cache (ATC) for devices to cache the DMA transactions. This option provides an interface between CPU and DMA Memory Management to a chipset's Address Translation and Protection Table to translate DMA addresses to host addresses. This option is set to Enabled by default.
- Adjacent Cache Line Prefetch
- Optimizes the system for applications that need high utilization of sequential memory access. This option is set to Enabled by default. You can disable this option for applications that need high utilization of random memory access.
- Hardware Prefetcher
- Enables or disables the hardware prefetcher. This option is set to Enabled by default.
- DCU Streamer Prefetcher
- Enables or disables the Data Cache Unit (DCU) streamer prefetcher. This option is set to Enabled by default.
- DCU IP Prefetcher
- Enables or disables the Data Cache Unit (DCU) IP prefetcher. This option is set to Enabled by default.
- Execute Disable
- Enables you to run the disable memory protection technology. This option is set to Enabled by default.
- Logical Processor Idling
- Enables you to improve the energy efficiency of a system. It uses the operating system core parking algorithm and parks some of the logical processors in the system which in turn allows the corresponding processor cores to transition into a lower power idle state. This option can only be enabled if the operating system supports it. It is set to Disabled by default.
- Configurable TDP
- Enables you to reconfigure the processor Thermal Design
Power (TDP) levels during POST based on the power and thermal delivery
capabilities of the system. TDP verifies the maximum heat the cooling
system is needed to dissipate. This option is set to Nominal by default.NOTE: This option is only available on certain stock keeping units (SKUs) of the processors.
- X2Apic Mode
- Enables or disables the X2Apic mode.
- Dell Controlled Turbo
- Controls the turbo engagement. Enable this option
only when System Profile is set to Performance.NOTE: Depending on the number of installed CPUs, there may be up to four processor listings.
- Number of Cores per Processor
- Controls the number of enabled cores in each processor. This option is set to All by default.
- Processor 64-bit Support
- Specifies if the processor(s) support 64-bit extensions.
- Processor Core Speed
- Specifies the maximum core frequency of the processor.
- Processor 1
- NOTE: Depending on the number of CPUs, there may be up to four processors listed.
The following settings are displayed for each processor installed in the system:
- Option
- Description
- Family-Model-Stepping
- Specifies the family, model, and stepping of the processor as defined by Intel.
- Brand
- Specifies the brand name.
- Level 2 Cache
- Specifies the total L2 cache.
- Level 3 Cache
- Specifies the total L3 cache.
- Number of Cores
- Specifies the number of cores per processor.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\