Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

Example of the show ip rip database Command to View Learned RIP Routes on Core 2

• To display Core 2 RIP database, use the show ip rip database command.
• To display Core 2 RIP setup, use the show ip route command.
• To display Core 2 RIP activity, use the show ip protocols command.

Core2(conf-router_rip)#end
                                 00:12:24: %RPM0-P:CP %SYS-5-CONFIG_I: Configured from console by console
                                 Core2#show ip rip database
                                 Total number of routes in RIP database: 7
                                 10.11.30.0/24
                                 [120/1] via 10.11.20.1, 00:00:03, TenGigabitEthernet 2/31
                                 10.300.10.0/24     directly connected,TenGigabitEthernet 2/42
                                 10.200.10.0/24     directly connected,TenGigabitEthernet 2/41
                                 10.11.20.0/24      directly connected,TenGigabitEthernet 2/31
                                 10.11.10.0/24      directly connected,TenGigabitEthernet 2/11
                                 10.0.0.0/8         auto-summary
                                 192.168.1.0/24
                                 [120/1] via 10.11.20.1, 00:00:03, TenGigabitEthernet 2/31
                                 192.168.1.0/24     auto-summary
                                 192.168.2.0/24
                                 [120/1] via 10.11.20.1, 00:00:03, TenGigabitEthernet 2/31
                                 192.168.2.0/24     auto-summary
                                 Core2#
                              

Core2#show ip route
                                 
                                 Codes: C - connected, S - static, R - RIP,
                                 B - BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated,
                                 O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1,
                                 N2 - OSPF NSSA external type 2, E1 - OSPF external type 1,
                                 E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1,
                                 L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default,
                                 > - non-active route, + - summary route
                                 
                                 Gateway of last resort is not set
                                 
                                 Destination Gateway            Dist/Metric Last Change
                                 ----------- ------- ----------- -----------
                                 C    10.11.10.0/24   Direct, TenGig 2/11          0/0   00:02:26
                                 C    10.11.20.0/24   Direct, TenGig 2/31          0/0   00:02:02
                                 R    10.11.30.0/24   via 10.11.20.1, TenGig 2/31  120/1 00:01:20
                                 C    10.200.10.0/24  Direct, TenGig 2/41          0/0   00:03:03
                                 C    10.300.10.0/24  Direct, TenGig 2/42          0/0   00:02:42
                                 R    192.168.1.0/24  via 10.11.20.1, TenGig 2/31  120/1 00:01:20
                                 R    192.168.2.0/24  via 10.11.20.1, TenGig 2/31  120/1 00:01:20
                                 Core2#  
                                 R    192.168.1.0/24  via 10.11.20.1, TenGig 2/31  120/1 00:05:22
                                 R    192.168.2.0/24  via 10.11.20.1, TenGig 2/31  120/1 00:05:22
                                 
                                 Core2#
                              

Core2#show ip protocols
                                 Routing Protocol is "RIP"
                                 Sending updates every 30 seconds, next due in 17
                                 Invalid after 180 seconds, hold down 180, flushed after 240
                                 Output delay 8 milliseconds between packets
                                 Automatic network summarization is in effect
                                 Outgoing filter for all interfaces is
                                 Incoming filter for all interfaces is
                                 Default redistribution metric is 1
                                 Default version control: receive version 2, send version 2
                                 Interface Recv Send
                                 TenGigabitEthernet 2/42 2 2
                                 TenGigabitEthernet 2/41 2 2
                                 TenGigabitEthernet 2/31 2 2
                                 TenGigabitEthernet 2/11 2 2
                                 Routing for Networks:
                                 10.300.10.0
                                 10.200.10.0
                                 10.11.20.0
                                 10.11.10.0
                                 
                                 Routing Information Sources:
                                 Gateway     Distance   Last Update
                                 10.11.20.1  120        00:00:12
                                 
                                 Distance: (default is 120)
                                 Core2#