Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Setting the Send and Receive Version

To change the RIP version globally or on an interface in the system, use the following command.

To specify the RIP version, use the version command in ROUTER RIP mode. To set an interface to receive only one or the other version, use the ip rip send version or the ip rip receive version commands in INTERFACE mode.

You can set one RIP version globally on the system using system. This command sets the RIP version for RIP traffic on the interfaces participating in RIP unless the interface was specifically configured for a specific RIP version.

  • Set the RIP version sent and received on the system. ROUTER RIP mode version {1 | 2}
  • Set the RIP versions received on that interface. INTERFACE mode ip rip receive version [1] [2]
  • Set the RIP versions sent out on that interface. INTERFACE mode ip rip send version [1] [2]

Example of an Interface Participating in the RIP Process

To see whether the version command is configured, use the show config command in ROUTER RIP mode. To view the routing protocols configuration, use the show ip protocols command in EXEC mode.

The following example shows the RIP configuration after the ROUTER RIP mode version command is set to RIPv2. When you set the ROUTER RIP mode version command, the interface (GigabitEthernet 0/0) participating in the RIP process is also set to send and receive RIPv2 (shown in bold). 

Dell#show ip protocols
                                 
                                 Routing Protocols is RIP
                                 Sending updates every 30 seconds, next due in 23
                                 Invalid after 180 seconds, hold down 180, flushed after 240
                                 Output delay 8 milliseconds between packets
                                 Automatic network summarization is in effect
                                 Outgoing filter for all interfaces is
                                 Incoming filter for all interfaces is
                                 Default redistribution metric is 1
                                 Default version control: 
                                 receive version 2, send version 2
                                 Interface        Recv  Send
                                 
                                 GigabitEthernet  0/0   2     2
                                 Routing for Networks:
                                 10.0.0.0
                                 
                                 Routing Information Sources:
                                 Gateway      Distance          Last Update
                                 
                                 Distance: (default is 120)
                                 
                                 Dell#

To configure an interface to receive or send both versions of RIP, include 1 and 2 in the command syntax. The command syntax for sending both RIPv1 and RIPv2 and receiving only RIPv2 is shown in the following example. 

Dell(conf-if)#ip rip send version 1 2
                                 Dell(conf-if)#ip rip receive version 2

The following example of the show ip protocols command confirms that both versions are sent out that interface. This interface no longer sends and receives the same RIP versions as the Dell Networking OS does globally (shown in bold). 

Dell#show ip protocols
                                 
                                 Routing Protocols is RIP
                                 Sending updates every 30 seconds, next due in 11
                                 Invalid after 180 seconds, hold down 180, flushed after 240
                                 Output delay 8 milliseconds between packets
                                 Automatic network summarization is in effect
                                 Outgoing filter for all interfaces is
                                 Incoming filter for all interfaces is
                                 Default redistribution metric is 1
                                 Default version control: 
                                 receive version 2, send version 2
                                 Interface          Recv   Send
                                 
                                 FastEthernet 0/0   2      1   2
                                 Routing for Networks:
                                 10.0.0.0
                                 
                                 Routing Information Sources:
                                 Gateway      Distance        Last Update
                                 
                                 Distance: (default is 120)
                                 
                                 Dell#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\