Dell PowerVault MD 32XX/36XX Series Storage Arrays CLI Guide

This section lists the CLI commands you can use to perform the following functions:

• Identify storage arrays
• Set passwords
• Add storage arrays
• Specify communication parameters
• Enter individual script configuration commands
• Specify a file containing script configuration commands

The following are general forms of the CLI commands, showing the parameters and terminals used in each command. The table below lists definitions for the parameters shown in the CLI commands.

SMcli 
                                 host-name-or-IP-address [
                                 host-name-or-IPaddress]
                                 [-c "
                                 command; {command2};"]
                                 [-n 
                                 storage-array-name | -w 
                                 WWID]
                                 [-o 
                                 outputfile][-p 
                                 password][-e][-S]
                              

SMcli 
                                 host-name-or-IP-address
                                 [
                                 host-name-or-IP-address] [-f 
                                 scriptfile]
                                 [-n 
                                 storage-array-name | -w 
                                 WWID]
                                 [-o 
                                 outputfile] [-p 
                                 password] [-e] [-S]
                              

SMcli (-n 
                                 storage-array-name | -w 
                                 WWID)
                                 [-c "
                                 command; {command2};"]
                                 [-o 
                                 outputfile][-p 
                                 password][-e][-S]
                              

SMcli (-n 
                                 storage-array-name | -w 
                                 WWID)
                                 [-f 
                                 scriptfile]
                                 [-o 
                                 outputfile] [-p 
                                 password] [-e] [-S]
                              

SMcli (-n 
                                 storage-array-name | -w 
                                 WWID)
                                 [-o 
                                 outputfile][-p 
                                 password][-e][-S]
                              

SMcli -a email:
                                 email-address
                                 [
                                 host-name-or-IP-address1
                                 [
                                 host-name-or-IP-address2]]
                                 [-n 
                                 storage-array-name | -w 
                                 WWID | -h 
                                 host-name |
                                 -r (
                                 host_sa | 
                                 direct_sa)]
                                 [-I 
                                 information-to-include][-q 
                                 frequency][-S]
                              

SMcli -x email:
                                 email-address
                                 [
                                 host-name-or-IP-address1
                                 [
                                 host-name-or-IP-address2]]
                                 [-n 
                                 storage-array-name | -w 
                                 WWID | -h 
                                 host-name |
                                 -r (
                                 host_sa | 
                                 direct_sa)] [-S]
                              

SMcli (-a | -x) trap:
                                 community,
                                 host-name-or-IP-address [
                                 host-name-or-IP-address1
                                 [
                                 host-name-or-IP-address2]]
                                 [-n 
                                 storage-array-name | -w 
                                 WWID | -h 
                                 host-name |
                                 -r (
                                 host_sa | 
                                 direct_sa)] [-S]
                              

SMcli -d [-w][-i][-s][-v][-S]

SMcli -m 
                                 host-name-or-IP-address -F 
                                 email-address
                                 [-g 
                                 contactInfoFile][-S]
                              

SMcli -A [
                                 host-name-or-IP-address
                                 [
                                 host-name-or-IP-address]] [-S]
                              

SMcli -X (-n 
                                 storage-array-name | -w 
                                 WWID |
                                 -h 
                                 host-name)
                              

SMcli -?