PowerEdge RAID Controller H745

This article provides information about how to delete a virtual disk using the Device Settings menu on a PowerEdge server. If your PowerEdge server is running the UEFI mode as a boot mode, the RAID BIOS is not displayed.

This article explains how to create a Virtual Disk using the System Settings menu.

This article provides information about how to boot past the Driver Health Manager Screen.

The "Predictive failure reported for disk x" error continues to be logged every 24 hours, even after the identified drive has been replaced. The issue only affects drives connected to PERC Controllers in RAID configuration.

This article provides the information of how to assign or unassign a global dedicated hot spare for a hard drive.

Dell Technical solutions information about various topics, hosted on the Dell TechCenter IT community platform

This article explains how to export the RAID controller log (TTYlog) directly from OpenManage Server Administrator (OMSA) using the interface or using the command lines.

This article shows how to add additional disks to a virtual disk or reconfigure a virtual disk.

When encryption is enabled on BOSS-N1, the system may stop during POST with the message: "No Boot Device Available or Operating System Detected."

This article explains how to load the PERC driver during Windows 2022 Installation. Without the PERC driver loaded, the installation wizard cannot find a storage location

This article provides information about various battery error codes, their possible causes, and examples.

This article explains the procedure to open a Service Request (SR) using the Dell support page. Get help fast for your Dell device. No more waiting on hold. No more tech headaches. Dell makes it simple to fix problems, schedule repairs, or get support—right from your device or our support website.

Learn about Dell PERC features.

This article provides information about how to import a foreign configuration RAID array on the system setup (F2) menu.

This article explains how to export the RAID controller log (TTY log) directly from RAID Controller (PERC).

This article provides information about how to check Virtual Disk Properties in System Setup for PowerEdge Server.

How to Install PERCCLI utility on Red Hat Linux, Ubuntu Linux, VMware ESXi, and Windows Server.

This article provides instructions on how to assign a hard drive as a global hot-spare on a PowerEdge RAID Controller (PERC)

PowerEdge R7525 with PowerEdge RAID Controller (H345, H745) experiences a significant I/O throughput drop during sequential read testing with over 10 SSD drives in non-RAID mode.

When attempting to save the PowerEdge RAID Controller (PERC) controller's event logs from within the Host Integrated Interface (HII), this process may take upwards of 20 minutes to complete.

Slow insertion of a SAS or SATA drive in PowerEdge 15G or 16G Servers with a PERC or HBA controller configuration causes a "No Access" bit to be set, leading to an inability to blink and unblink drives.

PowerEdge RAID Controller (PERC11, PERC10), Human Interface Infrastructure (HII) configuration utility, and iDRAC do not support array expansion.

This article addresses an issue with cache memory handling on PERC10 controllers.

This article describes the different type of controllers and the ways in which they should be reseated.

This article provides information about STOR042 error while creating a Virtual Disk.

This article provides information about how to create virtual disk in eHBA mode for PowerEdge RAID Controller 10.

This article provides information about the battery learn cycle. It consists of a controller performed battery calibration operation to periodically determine the condition of the battery. This operation cannot be disabled.

This article explains how to use commands to gather smart logs.

This article explains how to download, install, and use the Dell PowerEdge RAID Controller (PERC) Command-Line Interface (CLI) utility to manage your RAID controller. The utility is supported on PERC Series 8 and later family controllers on hosts running Windows, Linux, or ESXi. PERCCLI can also extract RAID controller logs which contain information that allows you or Dell Technical Support to determine the status of RAID controllers and the connected storage devices to narrow down possible sources of error.

This article provides instructions for the management and configuration of RAID arrays on a LSI MegaRAID 9361-8i, 9440, 9460, and 9341 RAID Controllers