PowerEdge RAID Controller H355 Front SAS

This article shows how to add additional disks to a virtual disk or reconfigure a virtual disk.

This article describes the different type of controllers and the ways in which they should be reseated.

This article explains the procedure to open a Service Request (SR) using the Dell support page. Get help fast for your Dell device. No more waiting on hold. No more tech headaches. Dell makes it simple to fix problems, schedule repairs, or get support—right from your device or our support website.

Linux host reports reduced storage performance when using PERC or HBA controllers with attached SSD or NVMe devices.

This article provides instructions on how to assign a hard drive as a global hot-spare on a PowerEdge RAID Controller (PERC)

This article provides information about how to import a foreign configuration RAID array on the system setup (F2) menu.

When attempting to save the PowerEdge RAID Controller (PERC) controller's event logs from within the Host Integrated Interface (HII), this process may take upwards of 20 minutes to complete.

This article provides information about how to manage the Dell PowerEdge RAID Controller (PERC) using the PERCCLI utility.

The controllers are not detected during system boot when the Dell PowerEdge system is configured in BIOS (Legacy) Mode after updating the firmware of the PERC H350 or H355 RAID controllers to version 52.30.0-6115. This issue does not occur when the system operates in UEFI Mode, which is the default setting.

When encryption is enabled on BOSS-N1, the system may stop during POST with the message: "No Boot Device Available or Operating System Detected."

Slow insertion of a SAS or SATA drive in PowerEdge 15G or 16G Servers with a PERC or HBA controller configuration causes a "No Access" bit to be set, leading to an inability to blink and unblink drives.

Information about how drives behind a PERC are NOT detected in Windows/VMware ESXi Installation if Firmware Device Order (FDO) is enabled.

OpenManage Server Administrator 10.1.0 for RHEL7, RHEL8, and SLES15 requires the 10.1.0.1 patch for specific 15G, 14G Intel, and AMD PowerEdge platforms that now ship with or have parts replaced with revised PERC 10, PERC 11, and Host Bus Adapter (HBA) controllers due to supply chain issues. Since these revised controllers only support specific server models, the OMSA 10.1.0.1 patch cannot be posted to the Dell Linux repository and must be installed separately.

This article provides information about how to boot past the Driver Health Manager Screen.

This article explains how to export the RAID controller log (TTYlog) directly from OpenManage Server Administrator (OMSA) using the interface or using the command lines.

This article explains how to create a Virtual Disk using the System Settings menu.

This article explains how to download, install, and use the Dell PowerEdge RAID Controller (PERC) Command-Line Interface (CLI) utility to manage your RAID controller. The utility is supported on PERC Series 8 and later family controllers on hosts running Windows, Linux, or ESXi. PERCCLI can also extract RAID controller logs which contain information that allows you or Dell Technical Support to determine the status of RAID controllers and the connected storage devices to narrow down possible sources of error.

This article provides information about Double Faults and Punctures in a RAID array and it also advises how to fix the problem.

This article provides information about Intelligent Mirroring and Enhanced RAID 10.

This article provides information about how to delete a virtual disk using the Device Settings menu on a PowerEdge server. If your PowerEdge server is running the UEFI mode as a boot mode, the RAID BIOS is not displayed.

This article lists the PowerEdge RAID Controllers (PERC) by series family (generation) for Dell systems. There are several types of PERC controllers available depending on internal or external storage connectors, maximum drive support, and RAID support.

Learn about Dell PERC features.

This article provides the information of how to assign or unassign a global dedicated hot spare for a hard drive.

This article explains how to export the RAID controller log (TTY log) directly from RAID Controller (PERC).

Dell Technical solutions information about various topics, hosted on the Dell TechCenter IT community platform

This article explains how to load the PERC driver during Windows 2022 Installation. Without the PERC driver loaded, the installation wizard cannot find a storage location

Dell PERC H355 Non RAID Disk Mode

How to Install PERCCLI utility on Red Hat Linux, Ubuntu Linux, VMware ESXi, and Windows Server.

This article provides instructions for the management and configuration of RAID arrays on a LSI MegaRAID 9361-8i, 9440, 9460, and 9341 RAID Controllers