PowerFlex Software

本文提供了 PowerFlex 软件文档的链接。

本文提供了 PowerFlex 机架、PowerFlex 设备、PowerFlex 自定义节点、VxFlex 就绪型节点、PowerFlex 软件、PowerFlex for AWS、PowerFlex for Azure 和 CloudLink 的文档链接。

Installation of SDC version 3.6.0.4 fails on Windows hosts.

This article describes the basic steps required to collect support data from a Kubernetes-based PowerFlex Manager Platform (PFMP) system and the PFMP installer. Support data is collected using a standalone, single-file utility, pfmp_support. As such, the utility's executable can be copied to and run on the host from which support data is to be collected. Using this utility does not require a functioning PFMP. As such, support data can be collected during PFMP installation or when the PFMP UI is inaccessible.

尝试更改存储池 （SP） 日志容量时，该按钮呈灰色显示且无法单击。

Unable to collect PFxM 4.x Troubleshooting Bundle. Log collection Job automatically ends in 60 seconds.

夏令时已更改，导致无法访问 UI

This section provides the PowerFlex Manager 3.X compatibility details for PowerFlex rack components.

This procedure describes how to add another IP address subnet for use by the MDM cluster. This addresses scenarios where the MDM cluster uses a single network, or when an existing network must be replaced by a different one or to simply add another network (to an already multiple-network cluster). The MDM supports up to eight networks.

清除设备错误。

在配置了 NVMe 设备的基于 Linux 或基于 ESXi 的 SVM 服务器 PowerFlex 系统中检索操作系统设备路径。

Retrieve the OS device path for a specific virtual drive (VD) in a Linux-based, Windows, or ESXi running PERCCLI server PowerFlex system with an H730p/H740p controller.

Retrieve the OS device paths in a Linux-based or ESXi based Storage Virtual Machine (SVM) server PowerFlex system with an HBA330 controller.

Configure network throttling to control the flow of traffic over the network.

尝试将现有 HCI 资源组重新添加到 PowerFlex Manager 时，客户可能会遇到静态路由配置错误。此问题会阻止成功添加资源组，并可能阻止计划内升级

get_info.sh - collect diagnostic information from a PowerFlex host and pack it into a support bundle

After MDM switchover, SDSs cannot reconnect and MDMs crash.

SDS gets decoupled - the system might experience DU occasionally if more than one SDS decouples concurrently or in case the SDS decouples during a rebuild.

When a vMotion clone of a VM guest is submitted, it takes a lot longer than expected. Scenario Due to an environmental configuration issue, there was contention on the vMotion configured NICs that conflicted with iSCSI and VxFlex SDC traffic, causing reduced performance.

SDS fails to start up.

重新启动 ESXi/SVM 后，SDS 会启动，但在 UI/CLI 中处于断开连接状态。

After following NDU flow and switching to 1_node MDM cluster, upgrading Secondary/TB MDMs and trying to put the back into the cluster, MDM throws an error.

Upgrade will not start/finish the Finalize step, since the MDM is shown in an upgrade state in progress.

When trying to create and map a volume to a Compute Node in OpenStack the operation is taking much more time (comparing to the other nodes) and the client is logging errors against the newly created device.

网络连接问题导致辅助 MDM 状态变为“Not synchronized”。

There is only one SDC that is having issues w/ performance.

SDS reports sockets closed without any network events or evidence of networking issues.

每当重新启动 SDC 时都会出现错误。PowerFlex 网关的 IO 超时。

Issue Description vSphere ESXi hosts hang and become inaccessible randomly after experiencing high latency within the datastores.

Issue Description Each SDS requires what appears to be a full rebuild when exiting maintenance mode.