PowerFlex custom node R650

戴尔为我们的许多硬件系统提供了客户可更换部件 (CRU) 计划。CRU 计划允许客户更换指定的硬件组件。有关为特定硬件系统指定为 CRU 的硬件组件的列表，请转至戴尔保修和维护页面。

如何更换 PowerEdge 服务器或 PowerFlex 设备中的 NVDIMM。

PowerEdge servers crash with PCIe fatal errors while updating Kioxia CM6 NVMe drive firmware.

CPUs can be perceived to be hot while server is idle.

When a PS1010 or PS1030 NVMe SSD is installed, a PSOD may occur during production or gathering Operating System (OS) logs.

Following the initial setup, the Intel Infrastructure Processing Unit (IPU) is unable to ping networks beyond its local network.

This is a new attribute that is seen in Server Configuration Profile exports. This attribute cannot be edited.

During the power counter roll-over for utilization, the power counter rolls over before the rollover counter. This leads to an erroneous power spike which may throttle the server.

When trying to register or de-register Alert Connector, PFxM UI shows error (500) or (VXFM0004)

Dell Samsung Serial Attached SCSI (SAS) PM1653 and PM1655 solid state drives may report excessive Sense Key faults 0x3, 0x11, 0x0, or 0x4, 0x29, 0x4. These faults have the potential to cause unexpected drive issues.

After an update to 7.00.00.00 or higher, the iDRAC9 web server may become inaccessible where the user has uploaded a custom or CA signed web certificate.

This article contains the initial steps to take on all PowerFlex performance-based issues when observing performance degradation, low Input Output Operations Per Second (IOPs), low MB per sec, or high latency.

作为 2023 年 12 月版本（工厂和 Web 发布）的一部分发布的适用于 Windows作系统的 PowerEdge 15G 和 16G 英特尔 Lewisburg C62xx 芯片组 Dell Update Package （DUP） 版本 10.1.19485.8386，包括来自英特尔的用于 Windows Defender 应用程序控制 （WDAC） 的非签名组件。 PowerEdge R6515/R7515 AMD Milan 芯片组 DUP 版本 2.18.30.202（2023 年 10 月）还被发现包含来自 AMD 的用于 WDAC 的非签名组件。 针对即将到来的 2024 年 3 月数据块的 PowerEdge 第 14 代英特尔平台芯片组 DUP 软件包版本 10.1.18807.8279 （#K69PV）已被发现存在与 WDAC（强制模式）相同的问题，因为它包含来自英特尔的非签名组件。

本文介绍如何将内部 HTTP 共享用于 4.x PowerFlex Manager 版本认证矩阵 （RCM）、Intelligent Catalog （IC） 和 ISO 上传。

The iDRAC is unable to connect to a Server Message Block (SMB) share when the optional "SMB3 share encryption" is enabled.

文章概述了 PowerFlex 节点在启动期间、中断后或安装时报告“非易失性双列直插式内存模块 （NVDIMM） 电池未就绪”的症状，这是由于电池未充电所致。

无法使用 PFxM 升级交换机操作系统。

详细介绍了适用于版本 4.X 的 PowerFlex 管理平台 （PFMP） 虚拟机的正常重新启动，包括标记、耗尽和重新启动 MVM，同时保持两个节点处于活动状态并检查 PostgreSQL 运行状况。在此过程的范围内，MVM1 是 postgres 领导者。最后耗尽并重新启动。

本文介绍了 PowerFlex 解决方案中的 MDM 群集的详细信息。

User has one node in the system where the NVDIMM battery status reports as 'Unknown' but that is not one of the three options listed for the status.

PowerFlex components such as the MDM are disconnecting and reconnecting quickly and frequently. Lost connection followed by connected found in MDM events Connecting after 80-190ms

以下过程说明如何在基于 Debian 的服务器上手动安装外部 SDC。 以下过程中的步骤与 Debian/Ubuntu 操作系统相关，包括 Proxmox 虚拟环境。

How to clear device errors on Dell PowerFlex using Presentation Server

This article documents the known symptoms that can occur when the iDRAC9 fails to receive accurate Platform ID information from the CPLD controller during iDRAC boot. This issue can be encountered after the iDRAC is rebooted independently from the host server.

In SLES15, the service name was changed to "sdc", from the commonly used service name "scini".

Attempting to upgrade the PowerFlex Production or MDS Gateway resource fails stating that it could not connect to LIA on a specific IP address.

PowerFlex R650 R750 nodes with Complex Programmable Logic Device (CPLD) firmware 1.0.7 or earlier may is unavailable at POST when BIOS 1.8.2 and iDRAC 6.00.30.202 are installed, triggering iDRAC PowerFlex alerts.

PowerFlex versions 3.0.1.6, 3.5.1.4, and 3.6.0.2 and lower have a bug that causes the rotation mechanism of the eventlog.db file to not work at all, which causes a continuous increase in the file size.

This article describes the basic steps required to collect support data from a Kubernetes-based PowerFlex Manager Platform (PFMP) system and the PFMP installer. Support data is collected using a standalone, single-file utility, pfmp_support. As such, the utility's executable can be copied to and run on the host from which support data is to be collected. Using this utility does not require a functioning PFMP. As such, support data can be collected during PFMP installation or when the PFMP UI is inaccessible.

This how-to explains the commands and shows the results of outputs for the same to retrieve your service tag using a command console. It is displayed as the system serial number.