Dell Chassis Management Controller Version 2.0 for PowerEdge FX2 and FX2s RACADM CLI Guide

Description

Sets the CMC IP address. It displays an error message if the requested operation could not be performed, or a success message, if the operation is completed successfully.

To use this subcommand, you must have the Configure Chassis Administrator permission.

Synopsis

• racadm getniccfg
• racadm getniccfg –m <module>,

  where –m must be one of the following values:

  • chassis: default state if -m is not specified

  • server-n: where n = 1 to 4

  • switch-n: where n = 1 or 2

• racadm setniccfg -d
• racadm setniccfg -d6
• racadm setniccfg -s < IPv4Address> < netmask> < IPv4 gateway>
• racadm setniccfg -s6 < IPv6 Address> < IPv6 Prefix Length> <IPv6 Gateway>
• racadm setniccfg -o
• racadm setniccfg —p [-6}
• racadm setniccfg [-m <module>] —k [<speed> <duplex>]
• racadm setniccfg [-i <slot>] —v [<vlan_id> <vlan_priority>]

Input

• -d — Enables DHCP for the NIC (default is “DHCP disabled”.)
• -d –6 — Enables AutoConfig for the NIC. It is enabled by default.
• -s — Enables static IP settings. The IPv4 address, netmask, and gateway can be specified. Otherwise, the existing static settings are used. < IPv4Address >, < netmask >, and < gateway > must be typed as dot-separated strings.

  racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1

• -s –6 — Enables static IPv6 settings. The IPv6 address, Prefix Length, and the IPv6 gateway can be specified.
• -o — Enable or disable NIC.
• -m<module> — Must be one of the following values:
  • chassis: Default state if - m is not specified.
  • server-n: where n=1–4
  • server-nx: where n=1–4; x=a-d (lower case)
  • switch-n: where n=1–2
• -i < slot> — Must be number n, where n=1 to 4
• -v — When performing on a switch, release and renew any DHCP lease on that port for the changes to be effective. The VLAN settings must be one of the following legal values:
  • no arguments imply remove vlan tag, not compatible with server-nx. For example (“server-4b”) notation
  • <vlan_id> 1 to 4000, 4021, and 4094 inclusive
  • vlan_priority> 0 to 7, inclusive
• -p — Disables IPV4 (default)/IPV6 protocol
• -k — Must be one of the following legal values:
  • no arguments imply autonegotiate
  • <speed> = 10, 100
  • <duplex> = half, full
• -r — Enable or disable redundant mode. The legal values are:
  • 1 — Enable
  • 0 — Disable

Example

• racadm setniccfg -s 192.168.0.120 255.255.255.0 192.168.0.1

• racadm setniccfg -d

• racadm setniccfg -d6

• Configuration of speed = 100Mbps and duplex= full duplex:

  racadm setniccfg -k 100 full

• Configuration of speed and duplex to autonegotiate:

  racadm setniccfig -k

• Configuration of redundant mode:

  racadm setniccfg -r 1

• Configuration of VLAN id and priority of a slot or all blades in a sleeve:

  racadm setniccfg -i 5 -v 1000 7

• Configuration of CMC to a static IPv6 address:

  racadm setniccfg -m chassis -s -6 2001:DB8::2 64 2001:DB8::1

• Configuration of server to use stateless autoconfiguration address:

  racadm setniccfg -m server-1 -d -6

• Configuration of VLAN id and priority for a switch:

  racadm setniccfg -m switch-1 -v 1000 7

• Removal of VLAN configuration from a switch:

  racadm setniccfg -m switch-1 -v