Dell OpenManage Deployment Toolkit Version 4.3 Command Line Interface Reference Guide

PDF

Enumerating Array Disks

The following table lists the RAIDCFG options, parameters, and pre-defined arguments for enumerating array disks (hard drives).

NOTE: You can also use pdisk or -pd instead of adisk or -ad to specify an array disk.

Table 1. Enumerating Array Disks (Hard Drives)
Mandatory Options and Arguments	Optional Parameters	Valid Parameters Arguments	Description
`-ad -c=id` or `adisk controllerid=id`	NA	NA	Lists all the array disks attached to the specified RAID controller. This option combination is mandatory. NOTE: The following example displays output of a Series 7 controller. NOTE: Software controller does not display the `NegSpeed`, `CapSpeed`, `Certified` and `Supported` parameters. Example: A:>raidcfg -ad -c=2 `Controller: PERC H700 Adapter` `**** Physical Drive **` `Vendor: DELL(tm)` `Model: ST9146703SS` `Protocol: SAS` `Media: HDD` `NegSpeed: 6144 Mbps` `CapSpeed: 6144 Mbps` `Certified: YES` `Supported: YES` `Location: 0:0:1` `Size: 139392 MB (136 GB)` `Avail: 0 MB` `** Physical Drive **` `Vendor: DELL(tm)` `Model: ST9146703SS` `Protocol: SAS` `Media: HDD` `NegSpeed: 6144 Mbps` `CapSpeed: 6144 Mbps` `Certified: YES` `Supported: YES` `Location: 0:1:1` `Size: 139392 MB (136 GB)` `Avail: 0 MB` `** Physical Drive **` `Vendor: DELL(tm)` `Model: ST9146703SS` `Protocol: SAS` `Media: HDD` `NegSpeed: 6144 Mbps` `CapSpeed: 6144 Mbps` `Certified: YES` `Supported: YES` `Location: 0:2:1` `Size: 139392 MB (136 GB)` `Avail: 139392 MB (136 GB)` `RAIDCFG Command successful!` `** Physical Drive **` `Vendor: DELL(tm)` `Model: ST9146703SS` `Protocol: SAS` `Media: HDD` `NegSpeed: 6144 Mbps` `CapSpeed: 6144 Mbps` `Certified: YES` `Supported: YES` `Location: 0:3:1` `Size: 139392 MB (136 GB)` `Avail: 139392 MB (136 GB)` `** Physical Drive ****` `Vendor: DELL` `Model: ST9146802SS` `Protocol: SAS` `Media: HDD` `NegSpeed: 3072 Mbps` `CapSpeed: 3072 Mbps` `Certified: YES` `Supported: YES` `Location: 0:4:1` `Size: 139392 MB (136 GB)` `Avail: 139392 MB (136 GB)` `RAIDCFG Command successful!`
	`-vd=id` or `vdisk=id`		Lists the array disks that make up the virtual disk on the specified RAID controller. This option combination is mandatory. Example: A:>raidcfg -ad -c=2 -vd=0 Controller: PERC 6/E Drive Vendor: FUJITSU Drive Model: MAP3367NC Drive Location: 0:0:0 Drive Size: 34680 MB Drive Avail: 0 MB `**** Physical Drive ****` `Drive Vendor: SEAGATE` `Drive Model: ST336607LC` `Drive Location: 0:1:0` `Drive Size: 34680 MB` `Drive Avail: 0 MB` RAIDCFG Command successful!
`-ad -c=id` or `adisk controllerid=id`	`-ad= ch:targ,ch:t arg,... adisk= channel:tar get, channel:tar get,...`	`< valid array disk>`	Displays information about the specified array disk. This option combination is mandatory. Example: A:>raidcfg -ad -c=2 -ad= 0:1,0:2 Controller: PERC 6/E `**** Physical Drive **` `Drive Vendor: SEAGATE` `Drive Model: ST336607LC` `Drive Location: 0:1:0` `Drive Size: 34680 MB` `Drive Avail: 0 MB` `** Physical Drive ****` `Drive Vendor: FUJITSU` `Drive Model: MAP3367NC` `Drive Location: 0:2:0` `Drive Size: 34680 MB` `Drive Avail: 34680 MB` RAIDCFG Command successful!