I appreciate you answering but the pinouts offered were for everything except the control panel cable. In the next reply from Cody, he suggests a user's web site which I went to. The site has all kinds of info that was exactly what I was looking for. Thanks again for trying to help.
Hi bbestler, I swaped out the motherboard in my dim 4100,I eventually plan on moveing the new P4 mobo and etc.into a new ATX case and put my 4100 back together for a spare tower.,,,,,,,, Dont know what mobo you have,,,,,,,I think some earlier mod dims may be wired like my 4100 below,,,,,hope this helps
rustymt
Dell diminsion 4100 Motherboard pin out Frount pannel cable
7 5 3 1 1<--red trace---hard dr led-- X X X X X X X X 2<--------------power led---- X X X X X X X 3<--------------hard dr led-- 8 6 4 2 4<--------------power led----- 5<--------------reset sw------ Motherboard connector 6<--------------power sw------ 1 hard dr led 7<--------------reset sw------ 2 power led 8<--------------power sw------- 3 hard dr led \--------------------------- 4 power led \---------notused--------- 5 reset sw \---------" " ""------ 6 power sw \------" ""------------- 7 reset sw \---" " "---------------- 8 power sw \------" "------------- \------" ""---------- (Figure 1) \-------" "------------ (Figure 2) Ribbon cable from frount Pannel
(16 conductor)
* "USE AS A GUIDE ONLY",,,,Rewire info for my Dell dim 4100, check your wring with an ohm/volt meter or trace out. (Figure 1),,,,Dell motherboard to new case. (Figure 2),,,,Dell case to new ATX motherboard.
Goonboy
2.4K Posts
0
March 28th, 2001 03:00
You might find what you need here.
"If you can't be a good example, then you'll just have to serve as a horrible warning." --Catherine Aird
DELL-Cody
2.2K Posts
0
March 28th, 2001 21:00
larrycollier
1 Rookie
•
3 Posts
0
March 29th, 2001 03:00
larrycollier
1 Rookie
•
3 Posts
0
March 29th, 2001 03:00
bbessler
1 Message
0
September 18th, 2001 02:00
for a dimension.
john0877
2 Posts
0
January 19th, 2003 22:00
mines a J8F2 though so the J9E1 doesnt help
if someone got the info and can post it somewhere it would be great
rustymt
292 Posts
0
January 20th, 2003 16:00
Hi bbestler, I swaped out the motherboard in my dim 4100,I eventually plan on moveing the new P4 mobo and etc.into a new ATX case and put my 4100 back together for a spare tower.,,,,,,,, Dont know what mobo you have,,,,,,,I think some earlier mod dims may be wired like my 4100 below,,,,,hope this helps
rustymt
Dell diminsion 4100
Motherboard pin out Frount pannel cable
7 5 3 1 1<--red trace---hard dr led--
X X X X X X X X 2<--------------power led----
X X X X X X X 3<--------------hard dr led--
8 6 4 2 4<--------------power led-----
5<--------------reset sw------
Motherboard connector 6<--------------power sw------
1 hard dr led 7<--------------reset sw------
2 power led 8<--------------power sw-------
3 hard dr led \---------------------------
4 power led \---------notused---------
5 reset sw \---------" " ""------
6 power sw \------" ""-------------
7 reset sw \---" " "----------------
8 power sw \------" "-------------
\------" ""----------
(Figure 1) \-------" "------------
(Figure 2)
Ribbon cable from frount Pannel
(16 conductor)
* "USE AS A GUIDE ONLY",,,,Rewire info for my Dell dim 4100,
check your wring with an ohm/volt meter or trace out.
(Figure 1),,,,Dell motherboard to new case.
(Figure 2),,,,Dell case to new ATX motherboard.
wyo_tom
1 Message
0
May 15th, 2004 17:00
His web address has changed.
http://www.roberthancock.com/dell/fpconn.htm