Unsolved
This post is more than 5 years old
2K Posts
0
50194
D600 STOP: c0000218 {Registry File Failure} cannot load the hive (file): 32\config\SOFTWARE
D600 STOP: c0000218 {Registry File Failure}
The registry cannot load the hive (file):
\SystemRoot\System32\config\SOFTWARE
or its log or alternate.
Is it corrupt, absent, or not writable.
Beginning dump of physical memory
Physical memory dump complete.
Contact your system administrator or technical support
BBraxton
2K Posts
0
October 21st, 2005 13:00
FUJITSU
Model MHT2060AH
PART NO. CA06377-B10600DL
SET. NO. NP0DT4728SN4 DATE 2004-07
RATING +5V 0.60A
REV. NO. A 0
TH-0P2364-26812-475-006N
Rev. A00 Made in Thailand
HDD S/N:NP0DT4728SN4
bar code: S00A4-C73-GKHLAGF-4740 CTNSTHPF20
Boot in safe mode returned to the original BLUE screen
BBraxton
2K Posts
0
October 21st, 2005 13:00
Ran diagnosics tests - All passed
"Last known good configuration (that worked)"
A problem has been detected and windows has been shut down to prevent damage to your computer.
The problem seems to be caused by the following file: savrt.sys
DRIVER_UNLOADED_WITHOUT_CANCELLING_PENDING_OPERATIONS
If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:
Check to make sure any new hardware or software is properly installed.
If this is a new installation, ask your hardware or software manufacturer for any windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing.
If you need to use Safe Mode to remove or disable componenets, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical information:
*** STOP: 0x000000CE (0xBAFC5842, 0x00000000, 0xBAFC5842, 0x00000000)
savrt.sys
BBraxton
2K Posts
0
October 21st, 2005 14:00
As I started to run the Windows setup I noticed after F6 prompt disappeared that I had the option of F2 for Automated System Recovery but now it wants a floppy diskette which I obviously do not have, so I assume it is not an option. [ I was imagining it going to an area of the hard drive and setting things back to factory. ]
Windows Setup
Please insert the disk labeled:
Windows Automated System Recovery Disk
into the floppy drive.
Press any key when ready.
BBraxton
2K Posts
0
October 21st, 2005 14:00
[ Time for lunch. ]
After I had Windows copy there again and re-boot
Black and white:
Windows could not start because the following file is missing or corrupt:
(Windows root>/system32\hal.dll
Please re-install a copy of the above file.
BBraxton
2K Posts
0
October 21st, 2005 18:00
ejn63
1 Rookie
1 Rookie
•
87.5K Posts
0
October 23rd, 2005 13:00
BBraxton
2K Posts
0
October 24th, 2005 10:00
dysnena
1 Message
0
December 2nd, 2005 00:00
BBraxton
2K Posts
0
December 2nd, 2005 09:00
dysnena
Those dates also confuse me. 1999 is when I (first) registered with DellTalk. My own magical solution was the step you replied to. For some reason, Full NFTS format resulted in a failure of the setup (re-installing Windows XP Professional after re-format). However, when I did a "Quick" format followed by the setup everything worked fine. I provide support on a grad school campus so get lots of opportunies (challenges). Details of your situation?
japs
1 Message
0
January 5th, 2006 01:00
hello
my computer stop working it asked how i want to start my computer then after choosing goes to a blue screen whixh says;
STOP: c0000218(Registry File Failure) the registery cannot load the Hive (File):(and some stuff then it says) or its log or alternate. It is corrupt absent or not writable. Beginning dump of physical memory physical memory dump complete. contact your administrator or technical support group for further assistance.
i dont know much about computers but what should i do??
BBraxton
2K Posts
0
January 5th, 2006 10:00
What is the model of computer (Dimension? Optiplex? laptop?)
If a desktop, is it small form factor? Tower (medium)? Tower (large)?