May I know how to reinitialize "Dell Easy Setup Wizard Console"? My N3024 has initialized once, but I plan to configure everything from the very beginning stage.
Prior to doing the steps below, be sure to save your current configuration off to a server if you think you might need it later. To get back to the wizard you will need to wipe out the startup configuration. The commands are
delete startup_configuration
reload
If asked to save the configuration before reloading, say no. Upon reload the wizard should appear again.
So I have a N3024 which has been initialised previously and I don't know the IP address it's configured to use (can't access using the default 192.168.0.1).
I've pressed the 'reset' button on the front, but doesn't appear to have reset the IP.
Any ideas how I can access the configuration please?
Boot Utility Menu If a user is connected through the serial interface during the boot sequence, the operator is presented with the option to enter the Boot Utility Menu during the boot sequence. Selecting item 2 displays the menu and may be typed only during the initial boot up sequence. Select startup option within 5 seconds, else Operational Code will start automatically... Operational Code Startup -- Main Menu 1 - Start Operational Code 2 - Display Boot Menu Select (1, 2)# 2 Enter the Boot Menu password:calvin Boot Menu Rev: 6.0 Operational Code -- Boot Main Menu 1 - Start Operational Code 2 - Select Baud Rate 3 - Retrieve Logs 4 - Load New Operational Code 5 - Display Operational Code Details 9 - Reboot 10 - Restore Configuration to Factory Defaults 11 - Activate Backup Image 12 - Start Password Recovery
eric at ikunik
3 Posts
0
April 24th, 2014 15:00
yes, N3024 switch. need to Initialize then configure it to my network.
eric at ikunik
3 Posts
0
April 25th, 2014 07:00
Thank you . I will do that.
miguellobato
1 Message
0
July 20th, 2015 09:00
Is the link still valid? I can't open it...
isospin
2 Posts
0
December 10th, 2015 01:00
May I know how to reinitialize "Dell Easy Setup Wizard Console"? My N3024 has initialized once, but I plan to configure everything from the very beginning stage.
Thank you...
vt1012
212 Posts
1
December 10th, 2015 07:00
Prior to doing the steps below, be sure to save your current configuration off to a server if you think you might need it later. To get back to the wizard you will need to wipe out the startup configuration. The commands are
delete startup_configuration
reload
If asked to save the configuration before reloading, say no. Upon reload the wizard should appear again.
-B
LordJones
1 Message
0
September 12th, 2022 20:00
So I have a N3024 which has been initialised previously and I don't know the IP address it's configured to use (can't access using the default 192.168.0.1).
I've pressed the 'reset' button on the front, but doesn't appear to have reset the IP.
Any ideas how I can access the configuration please?
Thank you.
DELL-Erman O
Moderator
•
3K Posts
0
September 13th, 2022 02:00
Hi, you can try to factory default as below pg 264 https://dell.to/3B8UouZ
Connect to the Switch From a Serial Null Modem Connection https://dell.to/3xiV28b
Changing the IP Address of a Dell PowerConnect 3024 or 5012 Switch https://dell.to/3DhdNMY
Boot Utility Menu
If a user is connected through the serial interface during the boot sequence,
the operator is presented with the option to enter the Boot Utility Menu
during the boot sequence. Selecting item 2 displays the menu and may be
typed only during the initial boot up sequence.
Select startup option within 5 seconds, else Operational Code will start
automatically...
Operational Code Startup -- Main Menu
1 - Start Operational Code
2 - Display Boot Menu
Select (1, 2)# 2
Enter the Boot Menu password:calvin
Boot Menu Rev: 6.0
Operational Code -- Boot Main Menu
1 - Start Operational Code
2 - Select Baud Rate
3 - Retrieve Logs
4 - Load New Operational Code
5 - Display Operational Code Details
9 - Reboot
10 - Restore Configuration to Factory Defaults
11 - Activate Backup Image
12 - Start Password Recovery
Hope that helps!