Skip to main content
Start a Conversation

Unsolved

This post is more than 5 years old

maol

1 Message

10765

June 21st, 2004 08:00

Problems Ghosting a GX270

I have after lot´s of trouble managed to start a multicast ghost session on a dell gx270, but when ghost is trying to jump to the spanned image file(*.ghs file) I get the error messsage "Connection reset by server with GhostCode 19922". Does anyone have a clue of what to do??

SSD

1 Message

July 14th, 2004 19:00

we are having the same problems, and have tried a 3COM NIC with the same results.  NONE of the GX270's work.  However, when we run Ghost from a server with a 3COM card, it works - Intel server cards cause the failure.

jmccord1979

1 Message

December 29th, 2004 19:00

I am having a problem ghosting (7.5) a Dell OptiPlex GX270.  I downloaded the latest dos driver for the Intel on board NIC  from Dell and I created a new network boot disk.  The problem is on the boot up process of the GX270.  It looks like it binds ok and the mouse driver is installed but after the mouse installation is complete... it freezes.  Below is the boot up screen that I get while trying to boot to the mentioned network boot disk:
 
Intel Pro/1000 Network Connections Driver V3.57 051304
Copyright 2000-2004, Intel Corportation. All rights reserved
Single Network Interface Connection Found In Slot 0x0160
Slot Not Specified for Instance 1.
Loading on PCI Device VEN_8086&DEV_100E&SUBSYS_01511028&REV_02 In Slot 0x0160
Media: Copper Autonegotiated Speed/Duplex: 100MBPS Full Duplex
Permanent MAC Address:000D569A8DBA
      Current MAC Address:000D569A8DBA
 
MS-DOS LAN Manager V2.1 Netbind
IBM Netbind Version 2.1
Microsoft Mouse Driver Version 8.20
Copyright Microsoft Corp. 1983-1992.
Copyright IBM Corp. 1992-1993.
Mouse Driver Installed
Loading. . . .
 
Any help would be greatly appreciated!
 
Thanks,
 
John

IT Junkie

59 Posts

January 6th, 2005 16:00


@jmccord1979 wrote:
I am having a problem ghosting (7.5) a Dell OptiPlex GX270.  I downloaded the latest dos driver for the Intel on board NIC  from Dell and I created a new network boot disk.  The problem is on the boot up process of the GX270.  It looks like it binds ok and the mouse driver is installed but after the mouse installation is complete... it freezes.  Below is the boot up screen that I get while trying to boot to the mentioned network boot disk:
 
Intel Pro/1000 Network Connections Driver V3.57 051304
Copyright 2000-2004, Intel Corportation. All rights reserved
Single Network Interface Connection Found In Slot 0x0160
Slot Not Specified for Instance 1.
Loading on PCI Device VEN_8086&DEV_100E&SUBSYS_01511028&REV_02 In Slot 0x0160
Media: Copper Autonegotiated Speed/Duplex: 100MBPS Full Duplex
Permanent MAC Address:000D569A8DBA
      Current MAC Address:000D569A8DBA
 
MS-DOS LAN Manager V2.1 Netbind
IBM Netbind Version 2.1
Microsoft Mouse Driver Version 8.20
Copyright Microsoft Corp. 1983-1992.
Copyright IBM Corp. 1992-1993.
Mouse Driver Installed
Loading. . . .
 
Any help would be greatly appreciated!
 
Thanks,
 
John


 

USB support is a pain with Ghost and the GX270s.  I recall seeing a thread here a day or two ago that had the answer for this

Was this post helpful?

View All

0 events found

No Events found!

Top