Wireless SUSE 9.3 not working! HELP

I am running SUSE Pro 9.3 on a DELL INSPIRON 1150 Laptop with a Broadcom BCM4306 802.11b/g Wireless LAN Controller (rev 03):

I folllowed all instructions on the WIKI page, I have a signal, I even seem to get an IP adress, but I have NO connection to the internet. I only get the IP adress on wlan0 with ifup wlan0 when eth0 is up. Following many threads in this forum and many others I always seem to get somewhere, but not where I want to be. Here are my details:
If anyone can help, I would be .......(more than happy)

linux:~ # ndiswrapper -l
Installed ndis drivers:
bcmwl5a driver present, hardware present

linux:~ # iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

wlan0 IEEE 802.11g ESSID:"Wireless" Nickname:"Bokke"
Mode:Managed Frequency:2.437 GHz Access Point: 00:A0:C5:5D:56:2E
Bit Rate=11 Mb/s Tx-Power:25 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-38 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:4170 Missed beacon:0

dsl0 no wireless extensions.

linux:~ # ifconfig
dsl0 Link encap:Point-to-Point Protocol
inet addr:84.157.149.6 P-t-P:217.0.116.69 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:1493 errors:0 dropped:0 overruns:0 frame:0
TX packets:1586 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:739726 (722.3 Kb) TX bytes:193979 (189.4 Kb)

eth0 Link encap:Ethernet HWaddr 00:0F:1F:21:15:C2
inet6 addr: fe80::20f:1fff:fe21:15c2/64 Scope:Link
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1537 errors:4 dropped:0 overruns:0 frame:2
TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0
collisions:3 txqueuelen:1000
RX bytes:781249 (762.9 Kb) TX bytes:253117 (247.1 Kb)
Interrupt:11

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:122 errors:0 dropped:0 overruns:0 frame:0
TX packets:122 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8463 (8.2 Kb) TX bytes:8463 (8.2 Kb)

wlan0 Link encap:Ethernet HWaddr 00:90:96:CF:F6:B7
inet addr:192.168.1.33 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::290:96ff:fecf:f6b7/64 Scope:Link
UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1
RX packets:82 errors:0 dropped:0 overruns:0 frame:0
TX packets:140 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:6334 (6.1 Kb) TX bytes:13179 (12.8 Kb)
Memory:fcffc000-fcffdfff


linux:~ # iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: 00:A0:C5:5D:56:2E
ESSID:"Wireless"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.437 GHz (Channel 6)
Quality:0/100 Signal level:-39 dBm Noise level:-256 dBm
Encryption key:off
Bit Rate:1 Mb/s
Bit Rate:2 Mb/s
Bit Rate:5.5 Mb/s
Bit Rate:11 Mb/s
Extra:bcn_int=100
Extra:atim=0

linux:~ # ifdown wlan0
wlan0 device: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Contro ller (rev 03)
linux:~ # ifup wlan0
wlan0 device: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Contro ller (rev 03)
wlan0 warning: using NO encryption
Starting DHCP Client Daemon on wlan0... . IP/Netmask: 192.168.1.33 / 255.255.255.0

........the one thing I do not understand is that my AP is configured with the IP 192.168.1.1 but I get the IP named above? Shouldn't they be the same?


...please help, everything is great with Linux, but the wireless part is getting on my nerves

thanks

Afrocharles