Search

Running a pair of S6010-ON switches on admittedly older code (9.11(0.0P9)).  Trying to place PBR on a VLAN to test redirection.  Why might the switch vlan be complaining about not being in layer-3 mode when it's clearly participating in BGP and routing??   S6010-1(conf-if-vl-500)#ip

Hi Team, Today, after the upgrade i executed "fsck corepartition" and the executed "power-cycle stack-unit 1" and upon reboot i found that B: partition went into "INVALID" state and now switch is left with only Partition A:. Upgraded couple of switches but faced this issue only with one switch. Ple

Hello together,I am trying to connect one of my DELL S5248F-ON switches to an existing network with CISCO switches. The connection should not be able to do much, it is enough if two VLANs are connected over it.Both switches (DELL and CISCO) have 25GB ports and corresponding SFP modules. The DELL swi

Office has N4064F layer 3 setup with default gateway to the firewall on VLAN10 to the Internet Datacenter has N4064F layer 3 setup with default gateway to the firewall on VLAN120 to the Internet Recently added a PTP Fiber connection between Office and Datacenter on Port 10 with VLAN1051 I then se

Hi,we have Dell switch Z9100 that works as a Leaf switch and caries L2 traffic. Some customers also use these switches as L3 and carry L3 traffic. Question: How can I check on the Dell Leaf switches if they carry L2 and L3 traffic? How to identify if switch carries L3 traffic? Are there any comma

hi all, I am trying to find connected devices to the dell switch I have here using show mac address-table and show arp, however, I have a problem the 'show mac address-table' lists the mac address for the device on port 27 as 00BB.C1CC.3A97 but the show arp tells me the mac address is B40E.

From a network perspective, if you see a device in the arp table on a router, can you tell if it's wireless based on the mac address? Does Dell use different OUIs on wireless network adapters than wired?

We have a few N4064F used as core SAN/LAN/Layer3 switches Want to separate services so the internal Layer 3 is done on dedicated switches, considering N4032F or another set of N4064F Network is not complicated and using static routing, want to switch to a dynamic routing protocol The question is

Hi all, I'm trying to write a python script to extract connected clients from a dell n2000 series switch, no luck at this stage... I use to use switch miner in the past for Cisco extraction to detect the phones connected to what port of the switch but im unable to achieve this with dell. Has anyone

I set up the switch and cannot login using the same login credentials. I tried to factory reset it but since then i have the when the switch boots up as shown below. I will appreciate your assistance and even more explanation on this issue. Version 2.19.1266. Copyright (C) 2020 American Megatrends

Hi, does anybody determine way to high cpu on N1500 stack after upgrading firmware to 6.8.0.1 due ssltHelperTask? The stack contains 4 x 1548p units. I rolled back to 6.7.1.10 because the switch had paketloss and high leadtime regularly: What I noticed too, after reloading the stack, the poe-

Hi, we have used dell ps 6248 switches in our lan network .all are curently working with update firmware version. some time all switches are hang and network are down i have checked with logs its not showing anything,stp is enable i thought its all about flooding or multicast flooding.kindly help

Hi, I notice that there are two firmware types for the N2200-ON switch series. One is referred to as Dell Networking version 6.8.x and the other as Dell EMC Networking version 6.7.x. Right now I'm running 6.6.3.15. Can I use any of them to upgrade the firmware? Best regards

Hello, I'm trying to convert my ACLs on some VLAN Interfaces to PBR, because I need Source Based Routing on these VLANs. I have some deny rules in my ACLs and tried to implement them in the following way: route-map Route_1 permit 20match ip address Routing_1_Dropset interface null0 This doesn't

I have a N3248PXE-ON and i am trying to configure IP Device Tracking. I have it set up and working, however I am getting IP addresses that will not fall off of the table when they go inactive. I know i can clear the table manually, but how or what is the command to have this happen automatically?&n

I have a pair of S4148T-ON:s running as part of a multi-rack SmartFabric. I would like to change the port profile on these switches, but the docs indicate that they will lose all configuration upon changing the profile. I assume that includes the SmartFabric settings as well. Can anyone advise on

Hi good morning. I have several stacks of DELL S3148P with unaligned boot partition. show boot system stack-unit allCurrent system image information in the system:===============================================Type Boot Type A B-------------------------------------------------------------------

I've got 2 Dell EMC Switches, an N2224X and an N3000. I have a fiber optic link AND a radio back-up link. Intent is that they provide redundancy using spanning tree. Both show link but only the radio link actually works. If we pull the radio link cable the fiber connection does not pick up. Radio l

Hi - I was looking to get some S4048-ON to do some testing on. I am a bit confused about the licensing on these switches.  Some say they only include ONIE, and some include OS9.  After a bit of research, it seems that OS9 can be installed without license, since it's included with the base

I have two stacked S4048 switches. When the command show ip interface brief is issued ports Te1/5-8 are missing. Interface IP-Address OK Method Status ProtocolTenGigabitEthernet 1/1 unassigned NO Manual up downTenGigabitEthernet 1/2 unassigned NO Manual up downTenGigabitEthernet 1/3 unassigne