Search Results (503)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
Hi Adjusting TCP mss will affect MP7800 ?
Question
•
Connectrix
Community Accepted Solution
I am going to migrate one ficon director from DCX to 8510B. To avoid any mainframe iocds change, I was thought to use the portaddress --bind command to change the fcid of the ports used by storage to be exactly the same as the old DCX. I was wondering when I perform the portaddress --bind
Question
•
Connectrix
Community Accepted Solution
Could some expert confirm to us that the following Brocade Switch Merging work without impact on the Existing Merged Production Pair Switches???? Thanks. 1. Existing Pair of Merged Switch (Firmware FOS 7.0.2) are of switchDomain 1 & 2 having the Merged Configuration defined and in effect.
Question
•
Connectrix
Community Accepted Solution
Can anyone point me to a white paper or perhaps offer some help on integrating Cisco MDS switches with Active Directory? I've read Cisco's guides, but am not getting anywhere with them. Thanks,
Question
•
Connectrix
Community Accepted Solution
We have 4 x EMC Brocade DS300B Switches that now having intermittent Power Supply and Temperature Problem reported several times a day, but nothing is found in the errdump event log. We have SiteScope regularly SNMP poll the 4 x switches every 10 minutes and found that there's the following SNMP
Question
•
Connectrix
Community Accepted Solution
Hi, We want to connect Brocade 6505 to Brocade DCX-4S. DCX-4S is using Virtual Fabric and Brocade 6505 doesn't support Virtual Fabric. I understand brocade 6505 could be connected to DCX-4S only if 6505 is configured as access gateway (NPIV). Is it correct? Or would be possible to connect 6505 (n
Question
•
Connectrix
Community Accepted Solution
Hello users and Experts, One of our big customer request that we evaluate the difference between Cisco and brocade offer about Monitoring tools and Advanced feature. Actually, they use Brocade Gen 5 Director and BNA with MAPS and they would to know if advanced function ant tools are better from Cis
Question
•
Connectrix
Community Accepted Solution
Wondering if anyone has used the ClearLink Diagnostic Port on their Connectrix B-Series switches. Any success stories or experiences that you can share??? Clearlink Diagnostic Port (D_Port) mode allows you to convert a Fibre Channel port into a diagnostic port for testing link traffic and
Question
•
Connectrix
Community Accepted Solution
Dear all we have to migrate a Hyper-V Cluster with 2 nodes from direct attached connectivity (to a VNX storage) to SAN (switched) environment that includes 2 new FC switches. Which steps we have to follow for this migration? Thanks and Regards George
Question
•
Connectrix
Community Accepted Solution
now we are seeing some odd alerts that we have not seen before: Warning false Thu Dec 22 2016 23:58:02 EST Monitoring and Alerting System notification - Rule fw_CPU_AH_75 violated. Obj:CHASSIS 0 &nb
Question
•
Connectrix
Community Accepted Solution
Hi folks, If i've got two HBA double ports on my server. Should i use both cards port A for disk and port B for tapes ? or should i dedicate a HBA for disk and one HBA for tapes.... And having a single point of failure on the server........ People says not to mix the trafic on the HBA. I unde
Question
•
Connectrix
Community Accepted Solution
We have 2 x Brocade DS-6505-B FC Switches joined together without any additional License required. However, if we connect 3 Brocade Switches together, do we need any additional License??? Thanks for any advise.
Question
•
Connectrix
Community Accepted Solution
All... EMC Support Matrix shows that for certain common MDS switch combinations, we support a max. of 56 domains per fabric. Cisco however supports 80 domains per fabric (2nd image below). We are bumping up against the EMC supported limit at my customer and this is causing some frustrat
Question
•
Connectrix
Community Accepted Solution
Hello, Quick question on available port bandwidth on a MDS9000 series SAN switch. Do FC ISLs and port channels (all ports for that matter) run at full duplex like Ethernet? So, if I have a port or ISL connected at 8Gb, I have 8Gb of bandwidth receiving and 8Gb of bandwidth transmitting? Or, do I
Question
•
Connectrix
Community Accepted Solution
Hello, This is the first migration i have had to do, right now we have 9148's and moving these to new 9706's. We have a port channel that consists of 4 4GB fiber links from our ONS. Our plan was to use 2 of these links and move them to the 9706 and get rid of the ISL. When we create t
Question
•
Connectrix
Community Accepted Solution
I have a couple of Brocade 6520 switches, connected over DWDM over 40 miles (60 kilometers). Let's focus on 1 fabric: Dear fellow ECN people, On the right (site 2) I have a host with 3 HBAs. HBA 2 is connected to fabric B (not shown), HBA 1 is connected to fabric A and I would like to use HBA 3
Question
•
Connectrix
Community Accepted Solution
Hi Experts, I would like to know about ISL & Port Aggregation for Cisco & Brocade Fabric Switches. Please post few diagrams (with respect to Core-Edge Technology) with which i can understand more about that. Regards Neesha
Question
•
Connectrix
Community Accepted Solution
Hello, I'm using the vdx6740 at VxRail ToR Switch.Firmware is 6.0.1a version. but I has been set in the VDX best practices, it can not set "ipv6 mld snooping querier enable"configuration of Vlan1. I can not be understand. Error is following. > Error(s): > vlan 1: %% Error: Configurati
Question
•
Connectrix
Community Accepted Solution
I am using CMCNE12.4.2 build 43: Every time I run a Technical Support save for a particular switch i get the message SupportSave Operation Failed. Reason : 256 : Remote Host:Could not connect to remote host. Has anyone seen this before ?
Question
•
Connectrix
Community Accepted Solution
Hello, I have found some documents to remove RPA but I am having hard time to find not replacement but decommissioning the Splitter in DCX switch. I would appreciated if someone care to share all the steps or related document links that requires from RPA and Splitter how to power off splitter in n
Question
•
Connectrix