I have an old Dell server that has a PERC h700 controller.  When I run perccli /c0 show all I get the following output that shows Controller Status = Needs Attention (See Below the bolded/underlined).  This server has started randomly rebooting and I thought it might be a drive issue but from below output I cannot see what is needing attention.  Any suggestions?

======================

Generating detailed summary of the adapter, it may take a while to complete.

Controller = 0
Status = Success
Description = None

Basics :
======
Controller = 0
Model = PERC H700 Integrated
Serial Number = 01R00D2
Current Controller Date/Time = 09/04/2020, 19:00:33
Current System Date/time = 09/04/2020, 19:00:36
SAS Address = 5a4badb02581d500
PCI Address = 00:03:00:00
Mfg Date = 01/28/10
Rework Date = 01/28/10
Revision No = A00

Version :
=======
Firmware Package Build = 12.0.1-0083
Firmware Version = 2.0.03-0729
Bios Version = 3.09.00
Preboot CLI Version = 02.00-013:#%00008
Ctrl-R Version = 2.00-0024
NVDATA Version = 2.02.0037
Boot Block Version = 2.00.00.00-0018
Bootloader Version = 01.250.04.219
Driver Name = percsas2.sys
Driver Version = 4.17.2.64

Bus :
===
Vendor Id = 0x1000
Device Id = 0x79
SubVendor Id = 0x1028
SubDevice Id = 0x1F17
Host Interface = PCI-E
Device Interface = SAS-6G
Bus Number = 3
Device Number = 0
Function Number = 0

Pending Images in Flash :
=======================
Image name = No pending images

Status :
======
Controller Status = Needs Attention
Memory Correctable Errors = 0
Memory Uncorrectable Errors = 0
ECC Bucket Count = 0
Any Offline VD Cache Preserved = No
BBU Status = 3072
PD Firmware Download in progress = No
Lock Key Assigned = No
Failed to get lock key on bootup = No
Lock key has not been backed up = No
Bios was not detected during boot = No
Controller must be rebooted to complete security operation = No
A rollback operation is in progress = No
At least one PFK exists in NVRAM = No
SSC Policy is WB = No
Controller has booted into safe mode = No

Supported Adapter Operations :
============================
Rebuild Rate = Yes
CC Rate = Yes
BGI Rate = Yes
Reconstruct Rate = Yes
Patrol Read Rate = Yes
Alarm Control = Yes
Cluster Support = No
BBU = Yes
Spanning = Yes
Dedicated Hot Spare = Yes
Revertible Hot Spares = Yes
Foreign Config Import = Yes
Self Diagnostic = Yes
Allow Mixed Redundancy on Array = No
Global Hot Spares = Yes
Deny SCSI Passthrough = No
Deny SMP Passthrough = No
Deny STP Passthrough = No
Support more than 8 Phys = Yes
FW and Event Time in GMT = No
Support Enhanced Foreign Import = Yes
Support Enclosure Enumeration = Yes
Support Allowed Operations = Yes
Abort CC on Error = Yes
Support Multipath = Yes
Support Odd & Even Drive count in RAID1E = No
Support Security = Yes
Support Config Page Model = Yes
Support the OCE without adding drives = No
Support EKM = No
Snapshot Enabled = No
Support PFK = No
Support PI = No
Support Ld BBM Info = No
Support Shield State = No
Block SSD Write Disk Cache Change = No
Support Suspend Resume BG ops = No
Support Emergency Spares = No
Support Set Link Speed = No
Support Boot Time PFK Change = No
Support JBOD = No
Disable Online PFK Change = No
Support Perf Tuning = No
Support SSD PatrolRead = No
Real Time Scheduler = No
Support Reset Now = No
Support Emulated Drives = No
Headless Mode = No
Dedicated HotSpares Limited = No
Point In Time Progress = No
Extended LD = No
Boot Volume Supported = No
Support Uneven span = No
Support Config Auto Balance = No
Support Maintenance Mode = No
Support Diagnostic results = No
Support Ext Enclosure = No
Support Sesmonitoring = No
Support SecurityonJBOD = No
Support ForceFlash = No
Support DisableImmediateIO = No
Support LargeIOSupport = No
Support DrvActivityLEDSetting = No
Support FlushWriteVerify = No
Support CPLDUpdate = No
Support ForceTo512e = No
Support discardCacheDuringLDDelete = No
Support JBOD Write cache = No
Support Large QD Support = No
Support Ctrl Info Extended = No
Support IButton less = No
Support AES Encryption Algorithm = No
Support Encrypted MFC = No

Supported PD Operations :
=======================
Force Online = Yes
Force Offline = Yes
Force Rebuild = Yes
Deny Force Failed = No
Deny Force Good/Bad = No
Deny Missing Replace = No
Deny Clear = No
Deny Locate = No
Support Power State = Yes
Set Power State For Cfg = Yes
Support T10 Power State = No
Support Temperature = No
NCQ = No
Support Max Rate SATA = No

Supported VD Operations :
=======================
Read Policy = Yes
Write Policy = Yes
IO Policy = Yes
Access Policy = Yes
Disk Cache Policy = Yes
Reconstruction = Yes
Deny Locate = No
Deny CC = No
Allow Ctrl Encryption = No
Enable LDBBM = Yes
Support FastPath = No
Performance Metrics = No
Power Savings = No
Support Powersave Max With Cache = No
Support Breakmirror = No
Support SSC WriteBack = No
Support SSC Association = No
Support VD Hide = No
Support VD Cachebypass = No
Support VD discardCacheDuringLDDelete = No

HwCfg :
=====
ChipRevision =
BatteryFRU = N/A
Front End Port Count = 0
Backend Port Count = 8
BBU = Present
Alarm = Missing
Serial Debugger = Present
NVRAM Size = 32KB
Flash Size = 8MB
On Board Memory Size = 512MB
CacheVault Flash Size = NA
TPM = Absent
Upgrade Key = Absent
On Board Expander = Absent
Temperature Sensor for ROC = Absent
Temperature Sensor for Controller = Absent
Upgradable CPLD = Absent
Current Size of CacheCade (GB) = 0
Current Size of FW Cache (MB) = 0

Policies :
========

Policies Table :
==============

------------------------------------------------
Policy Current Default
------------------------------------------------
Predictive Fail Poll Interval 300 sec
Interrupt Throttle Active Count 16
Interrupt Throttle Completion 50 us
Rebuild Rate 30 % 30%
PR Rate 30 % 30%
BGI Rate 30 % 30%
Check Consistency Rate 30 % 30%
Reconstruction Rate 30 % 30%
Cache Flush Interval 4s
------------------------------------------------

Flush Time(Default) = 4s
Drive Coercion Mode = 128MB
Auto Rebuild = On
Battery Warning = On
ECC Bucket Size = 15
ECC Bucket Leak Rate (hrs) = 24
Restore HotSpare on Insertion = Off
Expose Enclosure Devices = Off
Maintain PD Fail History = Off
Reorder Host Requests = On
Auto detect BackPlane = SGPIO/i2c SEP
Load Balance Mode = Auto
Security Key Assigned = Off
Disable Online Controller Reset = Off
Use drive activity for locate = Off

Boot :
====
BIOS Enumerate VDs = 1
Stop BIOS on Error = On
Delay during POST = 0
Spin Down Mode = None
Enable Ctrl-R = Yes
Enable Web BIOS = No
Enable PreBoot CLI = No
Enable BIOS = Yes
Max Drives to Spinup at One Time = 2
Maximum number of direct attached drives to spin up in 1 min = 0
Delay Among Spinup Groups (sec) = 12
Allow Boot with Preserved Cache = Off

High Availability :
=================
Topology Type = None
Cluster Permitted = No
Cluster Active = No

Defaults :
========
Phy Polarity = 0
Phy PolaritySplit = 0
Strip Size = 64 KB
Write Policy = WB
Read Policy = Adaptive
Cache When BBU Bad = Off
Cached IO = Off
VD PowerSave Policy = Controller Defined
Default spin down time (mins) = 0
Coercion Mode = 128 MB
ZCR Config = Unknown
Max Chained Enclosures = 1
Direct PD Mapping = Yes
Restore Hot Spare on Insertion = No
Expose Enclosure Devices = No
Maintain PD Fail History = No
Zero Based Enclosure Enumeration = Yes
Disable Puncturing = No
EnableLDBBM = Yes
DisableHII = No
Un-Certified Hard Disk Drives = Block
SMART Mode = Mode 6
Enable LED Header = No
LED Show Drive Activity = Yes
Dirty LED Shows Drive Activity = No
EnableCrashDump = No
Disable Online Controller Reset = No
Treat Single span R1E as R10 = Yes
Power Saving option = Enabled
TTY Log In Flash = No
Auto Enhanced Import = No
BreakMirror RAID Support = No
Disable Join Mirror = No
Enable Shield State = No
Time taken to detect CME = 60 sec

Capabilities :
============
Supported Drives = SAS, SATA
Boot Volume Supported = NO
RAID Level Supported = RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50
, RAID60, PRL 11, PRL 11 with spanningPRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span
Enable JBOD = No
Mix in Enclosure = Allowed
Mix of SAS/SATA of HDD type in VD = Not Allowed
Mix of SAS/SATA of SSD type in VD = Not Allowed
Mix of SSD/HDD in VD = Not Allowed
SAS Disable = No
Max Arms Per VD = 32
Max Spans Per VD = 8
Max Arrays = 128
Max VD per array = 16
Max Number of VDs = 64
Max Parallel Commands = 1008
Max SGE Count = 80
Max Data Transfer Size = 8192 sectors
Max Strips PerIO = 42
Max Configurable CacheCade Size(GB) = 0
Max Transportable VDs = 0
Min Strip Size = 8 KB
Max Strip Size = 1.0 MB

Scheduled Tasks :
===============
Consistency Check Reoccurrence = 168 hrs
Next Consistency check launch = NA
Patrol Read Reoccurrence = 168 hrs
Next Patrol Read launch = 09/05/2020, 03:00:00
Battery learn Reoccurrence = 2160 hrs
OEMID = Dell

Drive Groups = 3

TOPOLOGY :
========

------------------------------------------------------------------------------
DG Arr Row EID:Slot DID Type State BT Size PDC PI SED DS3 FSpace TR
------------------------------------------------------------------------------
0 - - - - RAID1 Optl N 136.125 GB dflt N N dflt N N
0 0 - - - RAID1 Optl N 136.125 GB dflt N N dflt N N
0 0 0 32:0 0 DRIVE Onln N 136.125 GB dflt N N dflt - N
0 0 1 32:1 1 DRIVE Onln N 136.125 GB dflt N N dflt - N
1 - - - - RAID50 Optl N 1.088 TB dflt N N dflt N N
1 0 - - - RAID5 Optl N 557.75 GB dflt N N dflt N N
1 0 0 32:8 8 DRIVE Onln N 278.875 GB dflt N N dflt - N
1 0 1 32:9 9 DRIVE Onln N 278.875 GB dflt N N dflt - N
1 0 2 32:10 10 DRIVE Onln N 278.875 GB dflt N N dflt - N
1 1 - - - RAID5 Optl N 557.75 GB dflt N N dflt N N
1 1 0 32:11 11 DRIVE Onln N 278.875 GB dflt N N dflt - N
1 1 1 32:12 12 DRIVE Onln N 278.875 GB dflt N N dflt - N
1 1 2 32:13 13 DRIVE Onln N 278.875 GB dflt N N dflt - N
2 - - - - RAID5 Optl N 836.625 GB dflt N N dflt N N
2 0 - - - RAID5 Optl N 836.625 GB dflt N N dflt N N
2 0 0 32:2 2 DRIVE Onln N 278.875 GB dflt N N dflt - N
2 0 1 32:3 3 DRIVE Onln N 278.875 GB dflt N N dflt - N
2 0 2 32:4 4 DRIVE Onln N 278.875 GB dflt N N dflt - N
2 0 3 32:5 5 DRIVE Onln N 278.875 GB dflt N N dflt - N
------------------------------------------------------------------------------

DG=Disk Group Index|Arr=Array Index|Row=Row Index|EID=Enclosure Device ID
DID=Device ID|Type=Drive Type|Onln=Online|Rbld=Rebuild|Dgrd=Degraded
Pdgd=Partially degraded|Offln=Offline|BT=Background Task Active
PDC=PD Cache|PI=Protection Info|SED=Self Encrypting Drive|Frgn=Foreign
DS3=Dimmer Switch 3|dflt=Default|Msng=Missing|FSpace=Free Space Present
TR=Transport Ready

Virtual Drives = 3

VD LIST :
=======

--------------------------------------------------------------------
DG/VD TYPE State Access Consist Cache Cac sCC Size Name
--------------------------------------------------------------------
0/0 RAID1 Optl RW Yes RWTD - OFF 136.125 GB OS Drive
1/2 RAID50 Optl RW Yes RWTD - OFF 1.088 TB F_Drive
2/1 RAID5 Optl RW Yes RWTD - OFF 836.625 GB EDrive
--------------------------------------------------------------------

Cac=CacheCade|Rec=Recovery|OfLn=OffLine|Pdgd=Partially Degraded|Dgrd=Degraded
Optl=Optimal|RO=Read Only|RW=Read Write|HD=Hidden|TRANS=TransportReady|B=Blocked|
Consist=Consistent|R=Read Ahead Always|NR=No Read Ahead|WB=WriteBack|
FWB=Force WriteBack|WT=WriteThrough|C=Cached IO|D=Direct IO|sCC=Scheduled
Check Consistency

Physical Drives = 12

PD LIST :
=======

-------------------------------------------------------------------------
EID:Slt DID State DG Size Intf Med SED PI SeSz Model Sp
-------------------------------------------------------------------------
32:0 0 Onln 0 136.125 GB SAS HDD N N 512B ST9146803SS U
32:1 1 Onln 0 136.125 GB SAS HDD N N 512B ST9146803SS U
32:2 2 Onln 2 278.875 GB SAS HDD N N 512B MBF2300RC U
32:3 3 Onln 2 278.875 GB SAS HDD N N 512B MBD2300RC U
32:4 4 Onln 2 278.875 GB SAS HDD N N 512B MBF2300RC U
32:5 5 Onln 2 278.875 GB SAS HDD N N 512B MBD2300RC U
32:8 8 Onln 1 278.875 GB SAS HDD N N 512B MBD2300RC U
32:9 9 Onln 1 278.875 GB SAS HDD N N 512B MBD2300RC U
32:10 10 Onln 1 278.875 GB SAS HDD N N 512B MBD2300RC U
32:11 11 Onln 1 278.875 GB SAS HDD N N 512B MBD2300RC U
32:12 12 Onln 1 278.875 GB SAS HDD N N 512B MBD2300RC U
32:13 13 Onln 1 278.875 GB SAS HDD N N 512B MBD2300RC U
-------------------------------------------------------------------------

EID-Enclosure Device ID|Slt-Slot No.|DID-Device ID|DG-DriveGroup
DHS-Dedicated Hot Spare|UGood-Unconfigured Good|GHS-Global Hotspare
UBad-Unconfigured Bad|Onln-Online|Offln-Offline|Intf-Interface
Med-Media Type|SED-Self Encryptive Drive|PI-Protection Info
SeSz-Sector Size|Sp-Spun|U-Up|D-Down/PowerSave|T-Transition|F-Foreign
UGUnsp-Unsupported|UGShld-UnConfigured shielded|HSPShld-Hotspare shielded
CFShld-Configured shielded|Cpybck-CopyBack|CBShld-Copyback Shielded