Data Domain: Konfigurowanie interfejsów fizycznych za pomocą interfejsu wiersza poleceń

Jeśli domena danych została przeniesiona do nowej lokacji i chcesz ponownie skonfigurować wszystkie nowe elementy, możesz również uruchomić configuration setup Polecenia.

Jeśli chcesz skonfigurować tylko sieć, pomiń configuration setup i użyj poleceń sieci z tego artykułu.

# config setup

Launch a utility program that prompts you to configure settings for the system, network, filesystem, CIFS, NFS, and licenses. Press Enter to cycle through the selections and confirm any changes when prompted. Choices include Save, Cancel, and Retry.

This command option is unavailable on Retention Lock Compliance systems. Use System Manager to change configuration settings. Role required: admin and limited-admin.

Polecenie net configuration umożliwia skonfigurowanie fizycznego interfejsu w Data Domain.

 # net config <ifname> [type {floating | fixed}]
                {[<ipaddr>] [netmask <mask>] | [<ipv6addr>] |
                [dhcp {yes [ipversion {ipv4|ipv6}]|no}]}
                {[autoneg] | [duplex {full | half} speed {10|100|1000|10000}]}
                [up | down] [mtu {<size> | default}]
                [txqueuelen <size>]
                                       Configure an Ethernet interface. Create
                                       an alias by giving an address to a new
                                       alias number. Destroy an alias by
                                       giving an address of zero. "

Example # net config ethXx x.x.x.x netmask x.x.x.x 

To clear a interface give a address of zeros. 

Example # net config ethXx 0.0.0.0

 
Użyj polecenia net route set gateway , aby zmienić domyślną bramę podczas wstępnej konfiguracji lub po przeniesieniu systemu Data Domain.
   

# net route set gateway {<ipaddr> | <ipv6addr>}
                                       Set the default gateway

Jeśli musisz dodać tylko bramę, możesz użyć przycisku net route add gateway .

# net route add gateway <ipv4addr> [interface <name>]
                                       Add a default gateway address,
                                       optionally to a specific interface

   

# net aggregate add <virtual-ifname> interfaces <physical-ifname-list>
                [mode {roundrobin |
                balanced hash {xor-L2 | xor-L3L4 | xor-L2L3} |
                lacp hash {xor-L2 | xor-L3L4 | xor-L2L3}
                [rate {fast | slow}]}]
                [up {<time> | default}]
                [down {<time> | default}]
                                       Add secondary interfaces to an aggregate
                                       interface. Mode must be given the first
                                       time

 # net aggregate del <virtual-ifname> interfaces {<physical-ifname-list> | all}
                                       Delete network interfaces from an
                                       aggregate interface

 # net aggregate modify <virtual-ifname>
                [mode {roundrobin |
                balanced hash {xor-L2 |xor-L3L4| xor-L2L3} |
                lacp hash {xor-L2|xor-L3L4|xor-L2L3}
                [rate {fast | slow}]}]
                [up {<time> | default}]
                [down {<time> | default}]
                                       Modify the configuration of an
                                       aggregate interface. Mode must be given
                                       the first time

 # net aggregate show
                                       Display all aggregate interfaces

 #  net config <ifname> [type {floating | fixed}]
                {[<ipaddr>] [netmask <mask>] | [<ipv6addr>] |
                [dhcp {yes [ipversion {ipv4|ipv6}]|no}]}
                {[autoneg] | [duplex {full | half} speed {10|100|1000|10000}]}
                [up | down] [mtu {<size> | default}]
                [txqueuelen <size>]
                                       Configure an Ethernet interface. Create
                                       an alias by giving an address to a new
                                       alias number. Destroy an alias by
                                       giving an address of zero. 

# net config addresses [type {floating | fixed}]
                                       Convert IP addresses to another type.

 # net create interface {<physical-ifname> | <virtual-ifname>}
                {vlan <vlan-id> | alias <alias-id>}
                                       Create a VLAN interface or an IP Alias Interface

 # net create virtual veth<id>
                                       Create a virtual interface

 # net destroy {<virtual-ifname> | <vlan-ifname> | <ipalias-ifname> }
                                       Destroy a VLAN or IP Alias or Virtual
                                       interface

 # net disable <ifname>  
                                       Disable an Ethernet interface

 # net enable <ifname>
                                       Enable an Ethernet interface

 # net failover add <virtual-ifname> interfaces <ifname-list>
                [primary <ifname>]
                [up {<time> | default}]
                [down {<time> | default}]
                                       Add network interfaces to a failover
                                       interface

 # net failover del <virtual-ifname> interfaces {<ifname-list> | all}
                                       Delete network interfaces from a
                                       failover interface

 # net failover modify <virtual-ifname> [primary {<ifname> | none}]
                [up {<time> | default}]
                [down {<time> | default}]
                                       Modify the primary network interface
                                       for a failover interface

 # net failover show
                                       Display all failover interfaces

 # net modify <virtual-ifname> bonding {aggregate | failover}
                                       Change the bond mode between failover
                                       and aggregate

 # net ping {<ipadddr> | <ipv6addr>| <hostname> [ipversion {ipv4 | ipv6}]}
                [broadcast] [count <n>] [interface <ifname>]
                [packet-size <bytes>] [path-mtu {do | dont | want}]
                [pattern <pattern>] [numeric] [verbose]
                                       Ping a host. Param 'broadcast' is for

 # net show all
                                       Display all networking information

 # net show config [<ifname>]
                                       Display the configuration for the Ethernet interface

 # net show hardware
                                       Display Ethernet port information

 # net show hostname [type {local|ha-system}]
                                       Display the hostname

 # net show settings
                                       Display Ethernet interface settings

 # net show stats [[ipversion {ipv4 | ipv6}] [all | listening] [detailed] |
                [ipversion {ipv4 | ipv6}] route | interfaces |
                [ipversion {ipv4 | ipv6}] statistics]
                                       Display network statistics

 # net troubleshooting duplicate-ip
                                       Detect duplicate IP in network

https://www.dell.com/support/kbdoc/en-us/000013760  Domena danych — przenoszenie domeny danych z jednej lokalizacji do innej
https://www.dell.com/support/kbdoc/en-us/000209434 konfigurowanie interfejsów fizycznych za pomocą graficznego interfejsu użytkownika (GUI)